Будь ласка, використовуйте цей ідентифікатор, щоб цитувати або посилатися на цей матеріал:
http://elartu.tntu.edu.ua/handle/123456789/2878
Назва: | Розроблення процедури визначення характеристик твердості і міцності сталей методом інструментованого індентування |
Інші назви: | Development of the procedure for determining the hardness and strength characteristics of steels by the instrumented indentation method |
Автори: | Каток, Олег Анатолійович Дроздов, О. Katok, O. Drozdov, O. |
Бібліографічний опис: | О. Каток. Розроблення процедури визначення характеристик твердості і міцності сталей методом інструментованого індентування / О. Каток, О. Дроздов // Вісник ТНТУ. — 2013. — Том 71. — № 3. — С.215-220. — (механіка та матеріалознавство). |
Дата публікації: | 12-сер-2013 |
Дата внесення: | 24-лют-2014 |
Видавництво: | Тернопільський національний технічний університет ім. Івана Пулюя |
Місце видання, проведення: | Тернопіль, Україна |
УДК: | 539.53 620.178.15 |
Теми: | нормативний документ метод інструментованого індентування характеристики міцності границя міцності границя плинності твердість за Брінеллем standard document instrumented indentation method hardness characteristics ultimate strength yield strength Brinell hardness |
Короткий огляд (реферат): | Для нормування процедури визначення характеристик твердості і міцності сталей методом інструментованого індентування в Інституті проблем міцності імені Г.С. Писаренка НАН України розроблено проект стандарту Національної академії наук України. Отримано позитивні результати щодо використання цього стандарту при визначенні стану металу зварного з’єднання №111 «гарячого» колектора з корпусом парогенератора та стінки труби (сталь 17Г1С-У) газопроводу. The draft standard for nondestructive testing of the material condition of critical structural elements during their manufacture, operation and repair was prepared by the National Academy of Sciences (NAS) of Ukraine. This standard document was developed basing on the experimental investigations performed at the G.S. Pisarenko Institute for Problems of Strength under the NAS of Ukraine. A test method for instrumented indentation in the macro-range of indentation forces and procedures for converting Brinell hardness and strength of steels from instrumented indentation curves has been established. The deviation of the hardness values, estimated according to this standard from tensile testing results, does not exceed 10%, and the deviation of the Brinell hardness values, estimated according to this standard from the data, obtained by the Brinell hardness test method, does not exceed 5%. The developed standard has been used in the evaluation of the metal condition of critical equipment after its service life. The results of determining the distribution of the strength and hardness characteristics for the metal of welded joint No. 111 of the “hot” collector to the steam generator nozzle and the gas pipe wall, determined by the instrumented indentation method, are presented as an example. |
URI (Уніфікований ідентифікатор ресурсу): | http://elartu.tntu.edu.ua/handle/123456789/2878 |
ISSN: | 1727-7108 |
Власник авторського права: | © „Вісник Тернопільського національного технічного університету“ |
Статус публікації : | Опубліковано раніше |
Тип вмісту: | Article |
Розташовується у зібраннях: | Вісник ТНТУ, 2013, № 3 (71) |
Файли цього матеріалу:
Усі матеріали в архіві електронних ресурсів захищені авторським правом, всі права збережені.