Будь ласка, використовуйте цей ідентифікатор, щоб цитувати або посилатися на цей матеріал: http://elartu.tntu.edu.ua/handle/123456789/5380

Назва: Дослідження особливостей електродугового наплавлення під флюсом стрічковими електродами різного поперечного перерізу
Інші назви: Research of pecliarities of electric arc surfacing under fluxusing tape electrodes of different cross-section
Автори: Татарин, Богдан Павлович
Підгурський, Микола Іванович
Мариненко, Сергій Юрійович
Mastenko, V.
Tataryn, B.
Pidgurskyi, M.
Marynenko, S.
Бібліографічний опис: Дослідження особливостей електродугового наплавлення під флюсом стрічковими електродами різного поперечного перерізу / В. Мастенко, Б. Татарин, М. Підгурський, С. Мариненко // Вісник ТНТУ — Тернопіль : ТНТУ, 2014. — Том 75. — № 3. — С. 132-144. — (Машинобудування, автоматизація виробництва та процеси механічної обробки).
Research of pecliarities of electric arc surfacing under fluxusing tape electrodes of different cross-section / V. Mastenko, B. Tataryn, M. Pidgurskyi, S. Marynenko // Bulletin of TNTU — Ternopil : TNTU, 2014. — Volume 75. — No 3. — P. 132-144. — (Manufacturing engineering and automated processes).
Дата публікації: 2-вер-2014
Дата внесення: 18-гру-2014
Видавництво: Тернопiльський національний технiчний унiверситет iменi Iвана Пулюя
Місце видання, проведення: Тернопіль
УДК: 621.79.92
Теми: електродугове наплавлення
стрічкові електроди
дуговий процес
флюс
електродна стрічка
густина струму наплавлення коефіцієнт наплавлення
шлак
коефіцієнт стійкості (стабільності) процесу
електрошлаковий процес
параметри режиму наплавлення
Electric arc surfacing
flux
tape electrodes
arc process
electrode tape
surfacing current density
surfacing rate
slag
the rate of process resistance (stability)
electroslag process
settings of the surfacing mode
Короткий огляд (реферат): Досліджено вплив електродугового наплавлення стрічковими електродами різного поперечного перерізу (різної товщини і ширини) під флюсом різних марок на характер зміни продуктивності процесу наплавлення, відносної маси шлаку при наплавленні, долі участі основного металу в наплавленому і коефіцієнта стійкості (стабільності) процесу наплавлення за струмом та на витрати флюсу, як одного з основних технологічних параметрів процесу наплавлення під флюсом.
In this article there was investigated the effect of electric tape surfacing using tape electrodes of different cross-section (different thickness and width) under flux of different marks on the variation of surfacing process performance, surfacing rate, the relative weight of the slag during surfacing, the share of the base metal in the weld and the coefficient of resistance (stability) of surfacing process using current, as well as on the flux consumption as one of the main technological parameters of the surfacing process under flux. While conducting the research process of electric arc surfacing using tape electrode with thickness of 0,5 and 0,7 mm and width from 20 to 200 mm under flux mark OF-10 and FC-18 the authors found that the increasing of type cross-section was followed by the increase of surfacing productivity and the slight decrease of surfacing rate. At the same time, there was observed some difference in the intensity of productivity increase and the surfacing rate decrease, depending on the mark of flux and the thickness of tape electrode. This is mainly due to a great share of heat released into the electrode gap on the melting of tape electrodes with large cross-section, which ensures high productivity of surfacing process under flux of OF-10 and FC-18 marks on the whole diapason of used width of electrodes, thus the surfacing productivity using the tape with the thickness of 0,7 mm is higher for 8,5–35% than the surfacing productivity using the tape with thickness of 0.5 mm. Meanwhile, at the lower tape width the difference is 32–35%, and for the maximum width – 8,5–13,5%. At the same time, while using the tape electrode with the width of 20–100 mm and the same thickness, the surfacing process productivity remains almost the same regardless of the mark of flux, and the increase of the width to 200 mm provides for the difference increase by 10–12%. The surfacing rate decreases with the increase of electrode tape width, regardless of its thickness and mark of flux; meanwhile, this regularity is observed when applying the tape with a width of 140 mm, and the further increase of its width to 200 mm does not change the value of the surfacing rate.
URI (Уніфікований ідентифікатор ресурсу): http://elartu.tntu.edu.ua/handle/123456789/5380
ISSN: 1727-7108
Власник авторського права: © „Вісник Тернопільського національного технічного університету“
Тип вмісту: Article
Розташовується у зібраннях:Вісник ТНТУ, 2014, № 3 (75)



Усі матеріали в архіві електронних ресурсів захищені авторським правом, всі права збережені.