DSpace Зібрання: Вісник Тернопільського національного технічного університету імені Івана Пулюя, 2013 рік, № 4 (72)Вісник Тернопільського національного технічного університету імені Івана Пулюя, 2013 рік, № 4 (72)http://elartu.tntu.edu.ua/handle/123456789/33112024-03-28T19:33:01Z2024-03-28T19:33:01ZІндуктивні сенсори для вихрострумової дефектоскопії високої роздільної здатностіЛепеха, Віктор ВолодимировичCherepov, S.Lepekha, V.http://elartu.tntu.edu.ua/handle/123456789/34082018-01-11T19:57:14Z2013-11-19T00:00:00ZНазва: Індуктивні сенсори для вихрострумової дефектоскопії високої роздільної здатності
Автори: Лепеха, Віктор Володимирович; Cherepov, S.; Lepekha, V.
Короткий огляд (реферат): Продемонстровано виготовлені індуктивні сенсори високої роздільної здатності для
вихрострумових перетворювачів. Сенсори були досліджені для визначення їх роздільної здатності в
скануючому дефектоскопі. Отримано двовимірні магнітні образи системи модельних дефектів, на яких
визначено реальну роздільну здатність сенсорів. Реальна роздільна здатність сенсорів становить
менше 50 мікрон. Типові розміри індуктивних сенсорів складають приблизно 1 мм у діаметрі при
довжині близько 5 мм. Наведено фото сенсорів на різних етапах виготовлення, а також фото системи
модельних дефектів та їх двовимірний магнітний образ. Також продемонстровано реальне магнітне
зображення зварного шва в алюмінії, отримане таким сенсором за допомогою скануючого
дефектоскопа. Зроблено висновок про перспективність використання сенсорів такого типу в новітніх
розробках вихрострумових дефектоскопів скануючого та матричного типів.; This paper presents the novel inductive sensors for the high-resolution eddy current scanning
heads used for non-destructive testing of the welded joints and material non-uniformities. The inductive coils,
used for magnetic excitation and detection of the inductive response, were wounded with 20 μm copper
wire on the ferrite core with diameter down to 300 μm. In this work we present the description of the
inductive sensors fabrication procedure, as well as their dimensions and pictures. The fabricated eddy current
sensors were fixed on the sensor holder, mounted on the computer controlled industrial 2D scanning system with
nominal spatial motion precision of 25 μm. The 2D magnetic images, obtained by recording sensor signal
in each point of the scanning range, were used to determine the sensor’s ultimate resolution in detection of
material non-uniformities (defects). The test samples, specially designed for this purpose, have artificially
created test defects with various dimensions and depth. The test samples were designed to model cracks and
corrosion pinholes in magnetic (steel) and non-magnetic (aluminum alloy) materials The two-dimensional
magnetic image of the test samples reveals the actual spatial resolution of the sensors, found to be less than 50
micrometers Moreover, the sensitivity of the developed inductive sensor is high enough not only to image point
like inclusions but also to image the therma stress zone in the aluminum welded joint, as shown in the paper.
The small size of the sensors, typically ~1 mm in diameter and ~5 mm in length, allows dense packaging of
multiple sensors into the compact multisensory scanning head of the matrix type. The size and sensitivity of the
presented eddy current sensors make them a promising candidate for application in the latest non-destructive
scanning diagnostics systems."2013-11-19T00:00:00ZПрограмна реалізація методу розв'язання розріджених числових систем лінійних алгебричних рівнянь в середовищі MatLabSemchyshyn, L.http://elartu.tntu.edu.ua/handle/123456789/34072018-01-11T19:39:26Z2013-11-19T00:00:00ZНазва: Програмна реалізація методу розв'язання розріджених числових систем лінійних алгебричних рівнянь в середовищі MatLab
Автори: Semchyshyn, L.
Короткий огляд (реферат): Запропоновано новий підхід до розв’язування розріджених систем лінійних алгебричних
рівнянь із блочними елементами. Проведено підрахунок кількостей записів та операцій при чисельній
реалізації алгоритму множення матриць. Охарактеризовано складність алгоритму з точки зору
комп’ютерної алгебри. Проведено порівняння запропонованого алгоритму та блочного методу прогонки.
Обчислено кількість записів для методу прогонки. Протестовано алгоритми розв’язання деяких типів
розріджених числових систем лінійних алгебричних рівнянь. Показано ефективність запропонованого
алгоритму.; New approach to the linear algebraic equations rarefied systems with block elements solution
and the method of rarefied systems with the specific ways of filling solution is suggested in the article. The
variables of the xi rarefied system of the linear algebraic equations into the finite matrix chain fractions are
decomposed. Calculation of the records number and operations under the numerical realization of the matrix
multiplication algorithm is conducted. The algorithm complication from the computer algebra point of view is
characterized. Comparison of the suggested algorithm and the block method of “prohonka” is carried out. The
number of records for the method of “prohonka” is calculated. The described algorithm is used in the case of
systems with the rarefied three-diagonal matrix.
Algorithms of some types rarefied numerical systems of the linear algebraic equations are tested. Three-
diagonal systems of the linear algebraic equations solution by the method of chain fractions. The high accuracy
of the suggested solution is shown.
Function ESSELS is written and tested for the linear algebraic equations with numerical elements
solution systems in the MatLab medium. This function implements the algorithm of the linear algebraic
equations solution using the method of cut-off systems. This algorithm allows to solve equation systems in two
ways:
– in the case of symmetrical filling (the quantity of under-diagonals equals the quantity of above-diagonals),
and when the quantity of matrix under-diagonals and the quantity of above-diagonals are different. For the
comparison of the MatLab packsge with regular programmes a small programme MatLab Band was written. It
realizes the procedure of the linear algebraic equations tape systems by means of MatLab. The results of both
systems comparison are carried out in the chart. Algorithms for the given test system of the average dimension
have a considerable advantages in comparison with the standard functions of the MatLab package. Efficiency of
the suggested algorithm is shown in the article. Theoretical and methodological basis of investigation comprise
methods of optimization and mathematic modeling.2013-11-19T00:00:00ZСтаціонарне температурне поле в оболонках з одностороннім багатошаровим покриттямГембара, Наталія ОлександрівнаLucko, J.Hembara, N.http://elartu.tntu.edu.ua/handle/123456789/34062018-01-11T19:39:29Z2013-11-19T00:00:00ZНазва: Стаціонарне температурне поле в оболонках з одностороннім багатошаровим покриттям
Автори: Гембара, Наталія Олександрівна; Lucko, J.; Hembara, N.
Короткий огляд (реферат): Запропоновано розрахункову модель для визначення стаціонарного розподілу
температури в оболонці довільної форми з одностороннім багатошаровим покриттям. Отримано
розв’язок задачі теплопровідності для оболонки з покриттям і закон зміни температури по товщині.
Для оболонок обертання відповідну задачу розв’язано у безрозмірних величинах.
Розглянуто оболонку з одностороннім багатошаровим покриттям, поверхні якої омиваються
зовнішніми середовищами з різними температурами. Матеріали оболонки та покриттів мають різні
теплофізичні характеристики. На контактних поверхнях оболонки і першого шару покриття та між
шарами виконуються умови ідеального теплового контакту. На зовнішніх поверхнях системи оболонка-
покриття відбувається теплообмін із середовищами за законом Ньютона.
Як приклад, досліджено стаціонарне температурне поле в циліндричній оболонці з одностороннім
чотиришаровим покриттям.; In the chemical industry and power engineering steel elements made as thin shells of
revolution are widely used. Such constructions while in service may be exposed to power and heat loads, and the
influence of different aggressive environments. For protection against high-temperature corrosion and thermal
protection multi-layer coatings are applied. The difference between the coefficients of linear expansion of shell
and coats creates a complex picture of the stress state, when the temperature changes. Thus, to obtain data on
the performance of these structures with coatings it is important to examine the distribution of temperature field
through the thickness.
An arbitrary shell with unilateral multilayer coating, the surface of which is washed by the external
environment with different temperatures is being examined. Materials of shell and coatings have different
thermo-physical characteristics. On the contact surfaces of the shell and first layer and between layers the
conditions of ideal thermal contact are being accepted. On the external surfaces of the shell and the coating
there is a heat exchange with the external environment according to Newton's law.
Mathematical model for the solution of stationary heat conduction problem for the shell with unilateral
multilayer coating was obtained. This analytical solution is relatively simple and convenient for practical use.
For the shells of revolution corresponding problem is solved in dimensionless terms.
As an example, the stationary temperature field in a cylindrical shell with a unilateral four-layer coating,
was investigated. Efficiency and sufficient accuracy of the results of this study were established by comparison
with solutions of the same problem obtained by finite element method.
Calculations allow to estimate the value of the maximum possible temperature of the shell and the coating
with external thermal influences. It was found that the main parameters of influence on the contact temperature
is the thermophysical characteristics of the coating. By the selection of them it is possible to achieve or intensify
the of heat transfer through the coating or to increase the insulation ability.2013-11-19T00:00:00ZНеполіноміальні моделі квантової теорії поля в евклідовому підходіMatskiv, R.http://elartu.tntu.edu.ua/handle/123456789/34052018-01-24T07:31:06Z2013-11-19T00:00:00ZНазва: Неполіноміальні моделі квантової теорії поля в евклідовому підході
Автори: Matskiv, R.
Короткий огляд (реферат): В рамках евклідової квантової теорії поля запропоновано метод вивчення
характеристичних функцій для евклідових функцій Гріна в моделі з експоненціальним лагранжіаном
взаємодії в двовимірному просторі при різних значеннях допоміжної константи зв’язку α і головної
константи зв’язку g . Доведено, що в двовимірному випадку і α 2 > 8π відповідна евклідова теорія є
тривіальною, а у випадку α 2 < 4π і достатньо великих значеннях g > 0 ця теорія нетривіальна при
усунутих об’ємному і ультрафіолетовому обрізаннях. Виконання аксіом Остервальдера – Шрадера для
евклідових функцій Гріна гарантує існування відповідної квантової теорії поля в аксіоматиці Гордінга –
Вайтмана.; New method of investigation of the Euclidean Green functions for the nonpolynomial models
of the quantum theory of field is proposed. The model with exponential interaction in the two-dimensional case is
analysed. The monography by B.Simon emphathises the importance of these models from the scientific and
methodical point of view. It should be noted, that at first the Wightman functions were used to state this theory.
But after K.Osterwalder had found the connection between the Wightman and the Euclidean Green functions
and the Nelson theorem of reconstruction had been proved, the construction of the relevant Euclidean model of
the quantum theory of the field was reduced to the application of the theory of relativity methods (theory of
Gaussian processes).
While constructive building of the Euclidean Green functions the notions of triviality and non-triviality of
the quantum theory of the field under removed ultra-violet and volume cut-offs, are of importance. The following
approach to the solving of this problem is proposed. Characteristic measure functions, absolutely continuous
relatively Gaussian measure are analysed. These functions are initiative ones for the Euclidean Green functions,
that is why constructive building of the characteristic functions, in fact, provides the building of the
mathematical model of the Euclidean theory of the field.
As in the Lagrangian interaction two constants, principle and auxiluary, are available, the investigation
α 2 > 8π and α 2 < 4π .
2
It has been found, that in the case α > 8π under removed ultra-violet cut-off the theory of the field is
is carried out separately for the case
trivial, that is, the Euclidean Green functions coinside with the relevant functions of the free quantum theory of
2
the field. In the case α < 4π the Euclidean theory of the field for the exponential interaction is non-trivial. In
this case the infinite system of the integral equations, which is solved in the correspondingly chosen Banach
space, has been obtained for the characteristic functions. The operator norm, which operates in this Banach
space, was found to be less than 1. Then, basing on the Banach theorem, it can be stated, that the only solution
of the equations system is available, and because of this volume and ultra-violet cut-offs can be removed. As a
result, the limitation in the form of unequality on the principle coupling constant, has been obtained.2013-11-19T00:00:00ZТемпературне поле скінченого термочутливого циліндра за конвективного теплообміну з середовищами змінних температурЗаводовська, Н.Popovych, V.Zavodovska, N.http://elartu.tntu.edu.ua/handle/123456789/34042018-01-11T19:55:04Z2013-11-19T00:00:00ZНазва: Температурне поле скінченого термочутливого циліндра за конвективного теплообміну з середовищами змінних температур
Автори: Заводовська, Н.; Popovych, V.; Zavodovska, N.
Короткий огляд (реферат): Розглянуто двовимірну нелінійну стаціонарну задачу теплопровідності для
термочутливого циліндра скінченої довжини. Враховано теплообмін на усіх поверхнях циліндра із
зовнішніми середовищами різних функційно-змінних температур. Розв’язок задачі побудовано з
використанням методу лінеаризувальних параметрів щодо визначення температурних полів у
термочутливих елементах конструкцій та скінчених інтегральних перетворень.; A lot of structural elements of modern technology take the form of a finite cylinder and in the
manufacture and operation are often subjected to significant temperatures (high and low level temperatures). To
ensure their reliable operation already at the design stage the detailed analysis of the temperature field and flow
conditions of heat exchange processes should be carried out taking full account of heterogeneity (due to the fact
that the physical and mechanical properties of materials depend on temperature changes) and actual operating
condition also (taking into account heat exchange on all surfaces the surrounding temperatures of which are not
constant).
The method of construction the solutions to two-dimensional nonlinear stationary heat conduction
problems on the example of thermosensitive cylinder with convective heat exchange is proposed. The convective
heat exchange with varying (on the coordinates) surroundings temperature through all cylinder surfaces is
considered. The two-step linearization (partial - by introducing the Kirchhoff variable and final - by using the
linearizing parameters method) is realized for solving the corresponding nonlinear heat conduction problem.
This method is effective for constructing analytical and numerical solutions of heat conduction problems for
thermosensitive bodies, if they have convective heat transfer conditions at their surfaces. This method involves
the construction of solution to the equation for Kirchhoff variable with a linear condition that includes certain
"linearizing parameters". The resulting linear problem for the Kirchhoff variable is solved by finite integral
transformation method.
The distribution of temperature field of cylinder and also the influence of material temperature-sensitivity
on it taking into account linear dependence of heat conduction factor is determined. The comparison of the
obtained solutions with solutions of similar problems for the permanent characteristics of the material and the
mid-integral characteristics values for a given temperature range is made.2013-11-19T00:00:00ZПроектування термоелектричних генераторних модулів з матеріалів на основі MgSi/MnSiБілинський-Слотило, Володимир РомановичМочернюк, Роман МиколайовичСкутельник, Д.Mikhailovsky, V.Bilynskyj-Slotylo, V.Mochernyuk, R.Skutelnyk, D.http://elartu.tntu.edu.ua/handle/123456789/34032018-01-11T20:08:39Z2013-11-19T00:00:00ZНазва: Проектування термоелектричних генераторних модулів з матеріалів на основі MgSi/MnSi
Автори: Білинський-Слотило, Володимир Романович; Мочернюк, Роман Миколайович; Скутельник, Д.; Mikhailovsky, V.; Bilynskyj-Slotylo, V.; Mochernyuk, R.; Skutelnyk, D.
Короткий огляд (реферат): Представлено результати комп’ютерного проектування секційних термоелектричних
модулів, модулів на основі функціонально-градієнтних матеріалів (ФГМ), а також каскадних структур
з матеріалів на основі MgSi/MnSi. Визначено оптимальні концентрації легуючих домішок для матеріалів
секцій і віток, оптимальні функції неоднорідності термоелектричних перетворювачів енергії та
значення термоелектричних параметрів у каскадних перетворювачах, використанням яких
забезпечується досягнення максимальної ефективності термоелектричних генераторних модулів у
діапазоні температур 323 – 773 К. Показано, що максимальна ефективність односекційних модулів з
матеріалів на основі силіцидів складає η≈6.5 %, двосекційних та модулів з ФГМ – η≈8.5 %, а каскадних
структур – η≈8.1 %. Встановлено, що для виготовлення секційного модуля необхідно затратити в 1.28
раза більше матеріалу, ніж для каскадного модуля за умови отримання однакової вихідної потужності.; Constantly increasing demand for energy sources and environmentally friendly generators
results in the growing interest in the industrial waste heat recuperation with the help of thermoelectrics. To
apply thermoelectric materials widely their high efficiency is a must, but the low cost of the initial components,
their mechanical stability and ecological safety are also of great importance. Therefore, the search for the low-
cost materials with high thermoelectric parameters and the design of thermoelectric generator modules on their
base belong to major topical tasks. A number of silicide-based thermoelectric materials that satisfy the above
mentioned requirements have been chosen as a result of literature data analysis.
The results of computer simulation of sectional thermoelectric modules, functionally grades materials
(FGM) based modules, as well as stage structures from silicide-based materials for industrial waste heat
recuperation and that of internal combustion engines and alike are presented in this work. For calculations, the
experimentally measured temperature concentration dependencies of the thermoEMF coefficient, electric and
thermal conductivities of the materials investigated were used.
The optimal concentrations of doping impurities for the material of sections and legs were defined,
together with the optimal functions of inhomogeneity of thermoelectric energy converters and the values of
thermoelectric parameters in cascade converters. By use of the said converters maximum efficiency is reached
for the thermoelectric generator modules in the temperature range of 323-773 K. Thus, single-stage silicide-
based modules performance equals η≈6.5 %, that of two-stage and FGM based modules are η≈8.5 %, and
η≈8.1 % for multi-stage structures. To produce the sectional module must be expended by 1.28 more material as
compared to cascade module at the same output power.2013-11-19T00:00:00ZПідвищення ефективності функціонування автоматизованих інформаційних систем на основі планування процедур їх удосконаленняКопп, В.Doronina, J.Kopp, V.http://elartu.tntu.edu.ua/handle/123456789/34022018-01-11T20:10:08Z2013-11-19T00:00:00ZНазва: Підвищення ефективності функціонування автоматизованих інформаційних систем на основі планування процедур їх удосконалення
Автори: Копп, В.; Doronina, J.; Kopp, V.
Короткий огляд (реферат): Розглянуто принципи підвищення ефективності функціонування автоматизованих
інформаційних систем на основі аналізу часу початку їх реінжинірингу, а також планування процедур
удосконалення в цілому. Побудовано комплекс марковських і напівмарковських моделей для визначення
показників надійності й продуктивності укрупнених кластерів автоматизованих інформаційних систем.; Both, the principles of raising the efficiency of automated information systems functioning by
analyzing the starting time of their re-engineering and improvement planning procedures in general are taken
into consideration. The complex of the Markov and semi-Markov models to determine the reliability and
productivity indices of enlarged clusters of automated information systems is built.
To choose the depth (level) of penetration of reengineering procedures the quantitative and qualitative
estimation is used. The depth of reengineering penetration is defined by the penetration coefficient correlated
with the possible automation level of a certain system element in particular or the whole system in general.
To determine the re-engineering starting time for the AIMS two approaches are used. The first one
determines the best reengineering starting time by estimating the expenses increase on the system service. The
second approach determines the average cycle time of the system on the basis of the semi-Markov model
construction.
The paper contains the numerical simulation of the distribution functions mean cycle time of dataset
service for the Erlang distribution under the conditions defined mathematical expectation and variance for the
time between failures, processing unit recovery time, set collection and dataset processing time
Results obtained in our work limit the efficiency level of AIMS subsystems. For the systems with clear
structural differentiation the estimation of the minimal acceptable level of the system performance indicator for
each structural unit is done. As a result, the constraints ensemble was obtained.
Thus, the obtained expressions for the structural components of AIMS can be used as limits of the
effectiveness of these subsystems, when making decision on the whole system re-engineering.
The novelty of this approach realization is the accounting of investments at the stage of the system
functioning after the beginning of moral obsolescence and correlation of these expenses with the efficiency of the
system ongoing improvement by estimation changes in the mean time of the system cycles. The total amount of
efforts (financial, intellectual, creative) on continuous improvement determines the particular starting time and
penetration depth of re-engineering procedures, which make possible to save due to the same factors providing
the revolutionary change of the system modernization.2013-11-19T00:00:00ZОсобливості електричних, світлотехнічних та експлуатаційних характеристик напівпровідникових джерел світлаКозак, Катерина МиколаївнаTarasenko, M.Kozak, K.http://elartu.tntu.edu.ua/handle/123456789/34012018-01-11T20:08:21Z2013-11-19T00:00:00ZНазва: Особливості електричних, світлотехнічних та експлуатаційних характеристик напівпровідникових джерел світла
Автори: Козак, Катерина Миколаївна; Tarasenko, M.; Kozak, K.
Короткий огляд (реферат): На основі аналізу та узагальнення отриманих експериментальних даних побудовано
алгебраїчну математичну модель електричних та світлотехнічних параметрів напівпровідникових
джерел світла. Встановлено, що світловипромінюючі діоди є єдиним з існуючих джерел світла, в яких у
процесі перехідного процесу розгорання відбувається падіння як світлового потоку, так і світлової
віддачі, а при діміруванні – зростання світлової віддачі.; Basing on the analysis and generalization of the obtained and published experimental data
there has been constructed an algebraic mathematical model of semiconductor light sources’ electrical and
lighting parameters in the form of five interrelated equations. It has been established that light emitting diodes
are the only existing light sources, in which a decrease in both the luminous flux and luminous efficacy takes
place during the transition process of glow, while under that of dimming – an increase of the light output. It has
been proved that the dynamics of the transition process of the decrease of the luminous flux of semiconductor
light sources from the moment of switching to the moment of transition into a steady state regime (with accuracy
sufficient for practical purposes) is described by the difference of decreasing and increasing exponential
functions of constants of time and integration of various magnitude, which make possible to evaluate the
contribution of each transient thermal resistance (the base of light emitting diode-radiator, radiator-
environment) to the process of the excessive heat transfer from a driver and LEDs to the environment. It has
been proved, that the decrease of the luminous flux during the transition process from the moment of switching
to the transition into the steady state regime within 10% range testifies the fact, that under this condition of
thermal regime of a lighting product the average duration of the light emitting diode glow will be close to the
nominal value claimed in the specifications and technical documentation. The 10% value excess of the luminous
flux decrease indicates the light emitting diodes’ p-n junction overheating above the allowable level, at which
both the luminous efficiency and average duration of glow will be lower than stated. There has been developed a
method of determining an optimal value of nominal current generated on the basis of LED lighting products in
terms of providing the necessary magnitude of an average duration of glow based on the investigation of
dependence of the relative decrease of their luminous flux on the current from the moment of switching to the
transition into the steady state regime, which make impossible to develop and produce substandard products.2013-11-19T00:00:00ZПараметри привода багатошпиндельного гайкокрутаНіщенко, Іван ОлексійовичКулинич, Іван ЯковичKulynych, A.Nishchenko, I.Kulynych, I.http://elartu.tntu.edu.ua/handle/123456789/34002018-01-11T20:04:59Z2013-11-19T00:00:00ZНазва: Параметри привода багатошпиндельного гайкокрута
Автори: Ніщенко, Іван Олексійович; Кулинич, Іван Якович; Kulynych, A.; Nishchenko, I.; Kulynych, I.
Короткий огляд (реферат): Представлено й проаналізовано кінематичну схему багатошпиндельного гайкокрута
ударної дії для розбирання і складання різьбових з’єднань кріплення коліс автомобілів. Отримано
математичні моделі технологічних параметрів багатошпиндельного гайкокрута – часу розгону до
максимальної кутової швидкості системи привода гайкокрута й крутного моменту ударного імпульсу
на шпинделі. Математична модель часу розгону системи привода отримана на основі теореми про
зміну кінетичної енергії цієї системи, а математична модель крутного моменту ударного імпульсу – на
основі теореми про збереження механічної енергії системи. Час розгону залежить від кутової
швидкості й потужності електропривода гайкокрута, маси обертових деталей системи привода, їх
діаметральних розмірів, а крутний момент, крім цього, ще залежить від жорсткостей кручення вала
маховика і шпинделя.; Kinematic diagram of percussive multiple-spindle power nut-driver for disassembly and
assembly of threaded connections of motor vehicle wheels is presented and a brief description of its operation.
The power nut-driver can fit in the nuts without damaging thread in case of their jamming owing to insignificant
torque that ensures unhampered screwing of all the nuts onto studs simultaneously. If any jamming of the nut
and stud threads occurs while fitting, a short-time reverse running of the spindles is activated from control panel
and another fitting attempt is made. Reverse running of the spindle ensures accuracy of mutual location of the
nut and stud necessary for fitting. After fitting and screwing on the nuts are tightened individually, and in the
case of unscrewing – individual release from tightening with the aid of angular impact momentum, activating
jaw-clutches of rotation transmission to spindles after acceleration of power nut-driver drive system.
Mathematical study of technological parameters of multiple-spindle nut-driver – time of acceleration to
maximum angular velocity of power nut-driver drive mechanical system and impact momentum torque on the
spindle has been carried out. Mathematical models of these parameters have been substantiated. Mathematical
model of the time of acceleration of the power nut-driver drive mechanical system was elaborated on the basis of
the theorem on the change of kinetic energy of the system. This time depends on angular velocity and capacity of
power nut-driver electric drive, weight of rotating parts of the drive system and their diameter dimensions.
Mathematical model of impact momentum torque of the spindle was obtained on the basis of the theorem on the
system mechanical energy conservation. Kinetic energy of rotating parts of the power nut-driver drive, the
flywheel, in particular is transformed into potential energy of the flywheel shaft and the spindle during their
rotation at the time of unscrewing or tightening of nuts. The torque depends on the same parameters as the
parameters of acceleration and, besides, on torsional stiffness of the flywheel shaft and the spindle.
This multiple-spindle power nut-driver as compared with the known single-spindle power nut-drivers
reduces the time for dismounting and mounting motor vehicle wheels. This is ensured by simultaneous capping
of the heads on all the nuts of the wheel and replacement of manual fitting by mechanical fitting.2013-11-19T00:00:00ZТехніко-економічне обґрунтування технологічного процесу сівби зернових культурНавроцька, Тетяна Дем’янівнаЛотоцький, Роман ІгоровичФльонц, Олег ВолодимировичPavelchuk, Y.Navrotska, T.Lototskyi, R.Flionts, O.http://elartu.tntu.edu.ua/handle/123456789/33992018-01-24T19:34:09Z2013-11-19T00:00:00ZНазва: Техніко-економічне обґрунтування технологічного процесу сівби зернових культур
Автори: Навроцька, Тетяна Дем’янівна; Лотоцький, Роман Ігорович; Фльонц, Олег Володимирович; Pavelchuk, Y.; Navrotska, T.; Lototskyi, R.; Flionts, O.
Короткий огляд (реферат): Одним із найважливіших технологічних заходів в аграрному виробництві є сівба
сільськогосподарських культур, тому ми привели економічне обґрунтування нового способу сівби
зернових культур підгрунтово-розкидним способом. Цей спосіб забезпечує кращі умови сівби, живлення і
раціонального використання поживних елементів, грунтів та сонячної енергії, що дасть можливість
підвищити врожайності на 10...15%. Крім цього, це дає можливість зменшити застосування хімічних
препаратів для боротьби з бур’янами і зменшує трудоємність вирощування зернових.; One of the most important production-effective measures in the agricultural production is the
sowing of agricultural crops, application of the under-soil broadcast sowing in particular. The most often this
problem arises while growing food grains, the area of feeding of which requires efficient application of the soil
minerals and solar energy. Besides, it makes possible to decrease the application of chemicals for weeds
removal.
The objective of the work is to raise the crop capacity due to the even distribution of seeds on the feeding
area basing on the power-saving technologies. New construction of the operating member- ploughshare, which
provides technological-economic interpreting of the production-effective process of food grains sowing, has
been proposed. To calculate the economic efficiency the main indices, which take into account the
manufacturing and maintenance of the row and experimental drills: saving of maintenance and labour expenses,
savings per year, additional expenses justification, grain production profitability, drills construction metal-
consumption, etc, have been found.
Analytical dependencies of determination the maintenance expenses for the driller operation unit have
been derived. The annual economic effect index was found as the difference of annual presented and
comparative variants as well as the metal-consumption of the ploughshare or machine construction.
Besides, new coefficients of the paying variation of the seeds even distribution on the feeding area, as
well as the increase of the seeds sowing row width in the under-ploughshare area, have been derived by the
authors.
It has been determined, that according to the main indices the experimental drill possesses higher
economic efficiency than that CСЗС-2.1. Application of the developed ploughshares makes possible to decrease
the maintenances expenses for 1 hectare of sowing by 30% and labour expenses by 32.9%. Annual decrease of
the expenses or the annual economic efficiency due to the application of experimental drill is 11968 hrns as
compared with that of the drill СЗС 2.1.2013-11-19T00:00:00ZДослідження коливань у механізмах з асинхронним приводомРомасевич, Юрій ОлександровичLovejkin, V.Romasevich, Yu.http://elartu.tntu.edu.ua/handle/123456789/33982018-01-24T19:40:42Z2013-11-19T00:00:00ZНазва: Дослідження коливань у механізмах з асинхронним приводом
Автори: Ромасевич, Юрій Олександрович; Lovejkin, V.; Romasevich, Yu.
Короткий огляд (реферат): Наведено аналіз коливних явищ, які виникають при розгоні асинхронного привода
механізму. При проведенні розрахунків використано двомасову динамічну модель. Зв’язок між
зосередженими масами механізму – пружно-в’язкий. Показано, що нехтування у розрахунках
електродинамічними перехідними процесами двигуна (використання статичної механічної
характеристики) може призвести до резонансу та перевантаження елементів механізму динамічними
зусиллями. Вказано способи забезпечення відсутності резонансу в механізмах, обладнаних асинхронним
приводом та наведено основні напрямки подальших досліджень.; The analysis of oscillatory phenomena that occur during acceleration of asynchronous drive
mechanism is presented in the article. In the calculations two-mass dynamic model was used. Generalized
coordinates of the mechanism and its drive are adopted to be angular. The constraint between localized mass of
mechanism is elastic- viscous. The equation of motion of a dynamical system with help of the numerical methods
has been solved.
The maximum dynamic moment in the elastic-viscous constraint of mechanism was found. The influence
of the values of the system parameters on the value of the dynamic forces in its elements is shown. In the
research the dynamic and static mechanical characteristics of the engine are used. Dynamic characteristic is
given in the form of equations in orthogonal coordinates fixed α and β.
It is shown that the neglection of in the calculation of electrodynamic transients of engine (use of static
mechanical characteristics) can lead to resonance and overload of elements of the mechanism of dynamic
forces.
The conditions of resonance in the mechanism, associated with the coincidence of the natural oscillation
frequencies of the mechanism with one harmonic frequency electromagnetic torque have been investigated. It is
shown that in the resonance appearance the width of the resonance zone, the attenuation coefficients of
pulsating component of the electromagnetic torque and damping coefficients of the mechanical parts of the
system are of great importance. Some considerations about the work of distributed parameter systems with an
induction engine have been stated.
The methods to ensure the absence of resonance in the mechanisms with asynchronous drive have been
presented. Basic directions of further researches are listed. In order to establish the degree of danger of
resonance for systems with distributed parameters it is necessary to carry out the numerical integration of
differential equations of motion of the system and to find the maximum force in the elements of machines and
mechanisms. Analytical dependences presented in the article are also shown in the graphical form.2013-11-19T00:00:00ZВплив теплозмін під час експлуатації парогонів тес на статичну тріщиностійкість сталі 15Х1М1ФКречковська, Галина ВасилівнаБабій, Л.Student, O.Krechkovska, H.Babiy, L.http://elartu.tntu.edu.ua/handle/123456789/33972018-01-12T09:10:21Z2013-11-19T00:00:00ZНазва: Вплив теплозмін під час експлуатації парогонів тес на статичну тріщиностійкість сталі 15Х1М1Ф
Автори: Кречковська, Галина Василівна; Бабій, Л.; Student, O.; Krechkovska, H.; Babiy, L.
Короткий огляд (реферат): Показано, що локальний параметр механіки руйнування – статична тріщиностійкість
(JIC), чутлива до зміни стану металу внаслідок деградації в експлуатаційних умовах. Виявлено, що
кількість зупинок технологічного процесу під час експлуатації сталі, орієнтація зразків (осьова й
тангенціальна) та місце їх розташування в перерізі стінки труб (біля зовнішньої та внутрішньої
поверхонь труб) впливають на рівень статичної тріщиностійкості. За однакової тривалості експлуатації
на головних парогонах ТЕС, але різної кількості зупинок блоків, які супроводжуються значними перепадами
температури в стінці труб, найбільше зниження рівня JIC сталі 15Х1М1Ф зафіксували для металу, що
переніс більшу кількість зупинок. Цим доказано, що показник JIC високочутливий до зміни стану
експлуатованого металу під впливом теплозмін. Проаналізовано механізми руйнування металу у вихідному
стані та після експлуатації, виділено вплив кількості пусків-зупинок технологічного процесу на інформативні
фрактографічні ознаки.; The main steam pipelines of TPP are subjected to a combined effect of number of
technological factors causing the degradation of steel. Lot of operational factors affect the workability of energy
equipment. Among these factors are hard temperature-force operating conditions (temperature of the steam
pipelines is up to 570oC and the steam pressure – 24 MPa) and hydrogenated environment. One more reason of
the loss workability of equipment was revealed recently. This is a frequent shutdown of the process caused by
exploitation of the blocks in a maneuvering mode.
It is known that fracture toughness (JIC) is a local parameter of fracture mechanics sensitive to changes in
the state of the metal as a result of its degradation in service conditions. It was shown that JR-curves
significantly differ for the steel 15Kh1M1F in virgin state and used for a same time (~2⋅105 h), but at different
numbers of process shutdowns on the steam pipeline. It was revealed that number of shutdowns during longtime
operation of steel and orientation of the specimens (axial and tangential) and its location in the cross section of
tube wall (near the outer or inner surface of the tube) affect the value of fracture toughness. At the same
operation time of steel on the main steam pipeline of TPP, but at different numbers of shutdowns the maximum
reduction of the JIC level was revealed for the 15Kh1M1F steel after more shutdowns. Consequently, JIC level is
the sensitive indicator of changes in the state of the metal under the influence of thermal cycles caused by
shutdowns.
The fractographic features of the steel in virgin state and after operation during the same time on the main
steam pipeline of TPP, but at different numbers of shutdowns were analyzed. The wide stretch zone with
following ductile fracture by forming of dimple structure was revealed on the fracture surface of steel in virgin
state. A few fractographic features were revealed on the fracture surfaces of long-time operated steel. That is,
the stretch zone on the fracture surface of the metal operated at smaller number of shutdowns is significantly
less than in the non-operated metal, but in the steel operated at larger number shutdowns - it disappears. Ductile
increment of cracks during static active loading of specimens of operated steel are essentially decreased and the
continuity of the crack fronts disappeared. At the stage of spontaneous fracture the steel operated at smaller number
shutdowns was destroyed by the mixed inter- and transgranular fracture, but the steel after more shutdowns –
practically only by intergranular fracture. Intergranular fracture was considered as an indicator of the weakening the
boundaries between the neighbouring grains.2013-11-19T00:00:00ZДослідження властивостей епоксикомпозитів, наповнених нанодисперсним алмазом, методом ІЧ-спектрального аналізу та оптичної мікроскопіїСапронов, Олександр ОлександровичBuketov, A.Sapronov, O.http://elartu.tntu.edu.ua/handle/123456789/33962018-01-12T09:08:31Z2013-11-19T00:00:00ZНазва: Дослідження властивостей епоксикомпозитів, наповнених нанодисперсним алмазом, методом ІЧ-спектрального аналізу та оптичної мікроскопії
Автори: Сапронов, Олександр Олександрович; Buketov, A.; Sapronov, O.
Короткий огляд (реферат): Досліджено динаміку адгезійних і когезійних властивостей композитів від вмісту часток
нанодисперсного алмазу. На кривих залежності властивостей епоксидних композитів від вмісту
наночасток алмазу доведено існування двох максимумів, які свідчать про різні механізми
структуроутворення композитів залежно від їх наповнення. Методом ІЧ-спектрального аналізу
встановлено, що при введенні часток наноалмазу (за оптимального вмісту) відбувається розкриття
епоксидних циклів з наступним утворенням первинних і вторинних амінів.; The dynamics of adhesive and cohesive properties of composites from the content of particles
nanodispersed diamond has been investigated. On the curves of dependence of adhesive, physical, mechanical
and thermal properties of epoxy nanocomposites on the diamond nanoparticles content the existence of two
peaks, testifying different mechanism of structure composites depending on their content has been proved. The
mechanism to improve properties of composites, which provide the appearance of the first peak due to the fact,
that for most of the content the effect of ultrasonic pre-treatment of compositions is realized. It causes the
activation of interfacial interactions and, consequently, improved material properties. The second maximum is
due to the fact that the filler formed around the outer surface layer of considerable thickness, and with our
advanced chemical interfacial interaction between the matrix formed the lattice structure with a high degree of
crosslinking.
The method of infrared spectral analysis explored the nature of chemical bonds that arise in the process
of structure of epoxy composites containing particles nanodiamonds. It has been found that the introduction of
nanodiamond particles (for optimal content) it has been the opening of epoxy cycles with the subsequent
formation of primary and secondary amines occurs. It testifies the extensive interaction of the filler
macromolecules with the sites on the surface of the filler.
Taking advantage of the optical microscopy the cracking surface of nanocomposite materials has been
investigated. In composites with the maximal content of particles the surface of globular nature with almost
uniform distribution of craters of about similar size and shape was observed. The obtained results indicate on a
uniform distribution of stresses in the composite volume, which makes possible to state the thermodynamic
equilibrium state of the system after switching.2013-11-19T00:00:00ZЗакономірності зміни механічних характеристик сталі 12Х1МФ з різних зон гину парогону ТЕССтудент, Олександра ЗиновіївнаНикифорчин, Ю.Svirska, L.Student, O.Nykyforchyn, Yu.http://elartu.tntu.edu.ua/handle/123456789/33952018-01-12T09:08:52Z2013-11-19T00:00:00ZНазва: Закономірності зміни механічних характеристик сталі 12Х1МФ з різних зон гину парогону ТЕС
Автори: Студент, Олександра Зиновіївна; Никифорчин, Ю.; Svirska, L.; Student, O.; Nykyforchyn, Yu.
Короткий огляд (реферат): Гини парогонів ТЕС характеризуються неоднаковою деформацією металу різних зон:
розтягненої, нейтральної, стисненої. Як результат – різні механічні властивості цих зон унаслідок
деградації. Досліджено міру деградації сталі 12Х1МФ з різних зон гину після 2,5·105 год її експлуатації у
системі парогонів ТЕС. Стан металу оцінювали за результатами візуального обстеження та за
механічними характеристиками за одновісного розтягу та удару на повітрі. Виявили, що максимальних
змін внаслідок експлуатації зазнають механічні характеристики сталі розтягненої та нейтральної зон
гину.; Hard temperature-power operating mode of the steam pipeline (vapor pressure up to 14 MPa,
temperature – up to 565 oC and a large number of shutdowns of the process), and long-term influence of an
aggressive hydrogenating environment on stressed metal promote degradation of its structure and reduce the
mechanical properties, which were ensured by their workability at the beginning of operation. Therefore, the
diagnostics of the technical state of metal of the steam pipeline ensures the reliability of their operation and
does not lose relevance to the power system of Ukraine with critically worn-out equipment.
Features of degradation of thermal power plant steam pipeline bending were caused by non-identical
conditions of deformation of the metal in different zones (tensile, compressed and neutral) of bend as on the
stage of production and the follow long-term operation. Due to the technological features of production and
peculiarities of the cross-sectional shape of bends the maximum tensile stresses occur in the tensile zone of
bending, where the wall thickness of tube is minimal. Mechanical properties of metal from different bend zones
were differed after long-term impact of stress.
The level of degradation of 12Kh1MF steel from different zones of bend after 2,5·105 hours of operation
in the steam pipeline system of TPP was evaluated in this paper. Technical state of metal was estimated by visual
inspection of bend and using mechanical characteristics determined at uniaxial tension and impact test on the
air. During visual inspection of outer surface of the pipe an axial cracks in the tensile zone of bend, caused by
high temperature creep, were detected. It was established that mechanical properties of operated steel from
tensile and neutral zones of bend is maximally changed. That is, the characteristics of plasticity, determined on
the tangential specimens were sensitive to changes in the technical state of steel. Reduction of area of metal from
tensile zone of bend is in 2 times lower than the minimum allowable value (27% and 55% respectively). Impact
toughness level of the metal from tensile zone of bend determined on specimens of both orientations was lower
than the regulated value for heat-resistant steels too. This confirmed that the brittle fracture resistance
characteristic is also highly sensitive to changes in the technical state of the pipeline bend metal. Taking into
account the fact that degradation of damaged bending has reached the maximum degree (since the bend has
been damaged during operation), the level of the impact toughness of the metal can be proved expediency of
stopping the exploitation the actual structural elements of steam pipeline.2013-11-19T00:00:00ZОсобенности динамических процессов в прокатных станах и их диагностические свойстваВеренев, В.Bolshakov, V.Verenev, V.http://elartu.tntu.edu.ua/handle/123456789/33942018-01-11T20:15:58Z2013-11-19T00:00:00ZНазва: Особенности динамических процессов в прокатных станах и их диагностические свойства
Автори: Веренев, В.; Bolshakov, V.; Verenev, V.
Короткий огляд (реферат): Приведены некоторые результаты измерений момента сил упругости в главных линиях
клетей прокатных станов и вибрации оборудования при захвате полосы валками. Установлен ряд
особенностей переходных процессов, связанных с технологией прокатки и состоянием оборудования.
Получены и обоснованы новые информативные и диагностические признаки.
Впервые предложено и обосновано в качестве диагностического признака использовать время
запаздывания реакции участков линии привода на ударную нагрузку.
Разработаны и в промышленных условиях опробованы новые методы и способы диагностики
угловых зазоров.; The results of measurements of the elastic force moment in the main line of the drive stand of
rolls and equipment vibration when biting of band by rollers are provided. A number of features of transients
associated with the technology of rolling and condition of the equipment is identified. New symptoms and
diagnosis information are received and justified.
For the first time the usage of time delay reaction in the biting of band rollers is proposed and justified as
a diagnostic indicator. The time delay depends on the equipment wear and corner clearance. The larger the
angular clearance the greater the delay time. Time lag is defined by signals of measurement of torque on the
driving shafts, and by the vibration sensors. The sensors are mounted on a rolling stand and frame along the
main line of the drive stand of rolls. The regularities of changes in the dynamic coefficient and delay time of the
drive stand of rolls with the wear and angular clearances on the spindle and motor areas are set.
New methods and ways to diagnose angular clearances based on measuring the moment of elastic force
and vibration equipment are developed and tested in an industrial setting. An algorithm for diagnosing the
technical condition of the spindle and motor areas as measured transients is developed. The method is
recommended for systems of vibration diagnostics development.2013-11-19T00:00:00ZОценка локальной прочности и повреждаемости хрупких материалов по параметрам статистического распределения экспериментальных данныхСорока, Е.Хворостяный, В.Шабетя, А.Трегубов, Н.Rodichev, Y.Soroka, E.Shabetia, A.Khvorostianiy, V.Tregubov, N.http://elartu.tntu.edu.ua/handle/123456789/33932018-01-11T20:16:10Z2013-11-19T00:00:00ZНазва: Оценка локальной прочности и повреждаемости хрупких материалов по параметрам статистического распределения экспериментальных данных
Автори: Сорока, Е.; Хворостяный, В.; Шабетя, А.; Трегубов, Н.; Rodichev, Y.; Soroka, E.; Shabetia, A.; Khvorostianiy, V.; Tregubov, N.
Короткий огляд (реферат): Проведен статистический анализ результатов испытаний листового стекла и
алюмокерамики при царпании со скалыванием индентором Роквелла. Определены параметры
распределения Вейбулла для экспериментальных результатов. Получены статистически обоснованные
значения параметра повреждаемости при вероятности разрушения от 0,01 до 0,99, что позволило
уточнить характеристики локальной прочности стекла и керамики и повысить достоверность
прогноза работоспособности материала при заданной вероятности разрушения ответственных
изделий. Показана неприемлемость линейной аппроксимации зависимости разрушающей нагрузки P от
расстояния разрушения L при локальном нагружении хрупких материалов. Для листового стекла в
области малых нагрузок обнаруженa аномально высокая повреждаемость, характеризующаяся
возможными размерами скола до 0,520 мм, что в три раза превышает предельные размеры сколов для
керамики Al2О3-1. Результаты могут быть использованы при выборе и оптимизации технологии
изготовления оптического стекла, дентокерамики и режущего керамического инструмента.; Local strength and the edge damageability of amorphous and crystalline brittle materials are
estimated by the methods of statistical analysis. The Weibull distribution is used to analyze experimental data of
scratching with edge chipping for the samples of float glass and dense ceramics Al2О3-1. The shape and the
scale parameters of the Weibull distribution for the experimental results on the edge destruction, depending on
the distance from the edge are determined. A fundamental difference in the mechanical behavior of amorphous
and crystalline brittle materials under the local loading is detected. Statistically valid values of damageability
parameter L for the fracture probability in the interval 0.01...0.99 are obtained. This allowed specifying the
characteristics of the local strength of glass and ceramics, and improving the reliability of the forecast
performance of the material at a given probability of failure. It is obtained, that dense ceramic is characterized
by non-linear S-shaped form of the plot of the fracture load P versus fracture distance L. In the range of high
loads of glass, a similar to ceramic S-shaped dependence P = f (L) is observed. Abnormally high damageability
for float glass in the range of small loads characterized by chipping to the possible size of 0.520 mm, which is
three times the size for chipping of ceramic Al2O3-1, is detected. It is shown that the estimation error in the
parameter of fracture resistance to chipping FRS at the failure probability of 1% as an average value of the ratio
P/L was 64% and 391% for ceramics and glass, respectively, compared with the predicted resistance to
chipping, defined on the basis of a probabilistic approach. This proves the unacceptability of the linear
approximation of the dependence P = f (L), which has been adopted in literature, especially for critical parts
made of the brittle materials. The results are the basis for a focused selection of brittle materials, depending on
their function. The results can be used for selecting and optimizing the manufacturing technology of optical
glass, dental ceramics and ceramic cutting tool.2013-11-19T00:00:00ZТеория реконструкции температурного поля на основе ультразвукового зондирования двухслойных стенок реакторовЗапорожец, О.Михайловский, В.Носарь, А.Dordienko, N.Zaporozhets, O.Mykhailovsky, V.Nosar, A.http://elartu.tntu.edu.ua/handle/123456789/33922018-01-22T16:18:31Z2013-11-19T00:00:00ZНазва: Теория реконструкции температурного поля на основе ультразвукового зондирования двухслойных стенок реакторов
Автори: Запорожец, О.; Михайловский, В.; Носарь, А.; Dordienko, N.; Zaporozhets, O.; Mykhailovsky, V.; Nosar, A.
Короткий огляд (реферат): Работа посвящена совершенствованию теоретической модели реструктуризации
теплового профиля Т(x,t) в двухслойной пластине с односторонним доступом по данным измерений
средней по толщине стенки х температуры <T>(t) при тепловом воздействии на недоступную
поверхность пластины. Модель предназначена для использования в методе ультразвукового
неразрушающего контроля УЗНК температурных полей и обусловленных ими термических напряжений
в корпусах ядерных реакторов ЯР типа ВВЭР в нестационарных тепловых условиях. Он реализуется
путем регистрации при внешних тепловых воздействиях изменений в реальном времени t времени
задержки УЗ сигнала τ(t) на выделенном участке стенки корпуса реактора, определении по данным УЗ
измерений средней по толщине стенки х температуры <T>(t)=f(τ,t), реструктуризации по
установленному на основе теоретической модели алгоритму теплового профиля и расчета
соответствующих Т(x,t) термических напряжений σ(x,t). В предыдущих работах с участием авторов
основой для расчета теплового профиля по данным <T>(t) использована модель одно- или двухслойной
полубесконечной пластины, а также однослойной пластины конечной толщины. При этом модель,
несмотря на хорошую согласованность с экспериментом при малых временах УЗНК и вблизи
приконтактной с теплоносителем зоны, не учитывает изменений температуры на поверхности
конструкции, что ограничивает временные рамки УЗ мониторинга и увеличивает погрешность
контроля. В данной работе получены выражения для теплового профиля Т(х,t) в двухслойной пластине
конечной толщины, которая нагревается с одной поверхности. Выражения использованы для
сравнительного анализа двух теоретических моделей при расчете теплового профиля по данным
предыдущих комплексных УЗ и термометрических исследований массивных образцов из корпусной стали
15Х2МФА при импульсной тепловой нагрузке. Установлено, что теоретическая и экспериментальная
временные зависимости температуры в сечении пластины (массивного образца) на фиксированном
расстоянии от зоны контакта с источником нагрева х=const хорошо описываются полиномом третьей
степени. Результаты реструктуризации Т(х,t) по алгоритму усовершенствованной модели для х=const
хорошо согласуются с данными термометрических измерений.; The paper is devoted to improvement of the theoretical model of restructuring thermal profile
Т(x,t) in the two-layer plate with one-way access based on measurements of average temperature <T>(t) by
thickness wall x under the thermal action on inaccessible plate surface. The model is designed to be used it in the
method of ultrasonic nondestructive testing (UNDT) of temperature fields and caused by them thermal stresses
in reactor vessels of the WWER type at non-stationary thermal conditions. It is implemented by recording during
the thermal actions of changes in real-time t delay signal τ(t) on a dedicated section of the reactor wall,
determining of the average temperature by wall thickness <T>(t)=f(τ,t) according to the ultrasound
measurements data, restructuring thermal profile via algorithm based on the theoretical model and calculating
corresponding to Т(x,t) thermal stresses σ(x,t). In previous researches, in which the authors were involved, the
basis for calculating the thermal profile according <T>(t) a one- or two-layer semi-infinite plate model and the
one-layer plate of finite thickness were used. Despite of good consistency with experiment at small times UNDT
and around near-contact with the coolant zone the model does not take into account the temperature changes on
the construction surface, which limits the time frame of ultrasound monitoring and increases method error. In
this paper expressions for the thermal profile Т(х,t) in two-layer plate of finite thickness, which is heated on one
surface were obtained. The expressions were used for comparative analysis of two theoretical models for the
calculation of the thermal profile according to the previous complex ultrasound and thermometric studies of bulk
samples of the vessel steel 15Cr2MFA under pulsed thermal loading. It was found that the theoretical and
experimental temperature time dependence in the cross section of plate (bulk sample) at a fixed distance from
the contact with a heat source х=const is well described by the third degree polynomial. Restructuring results of
Т(х,t) by the algorithm of improved model for х=const are in good agreement with the thermometric
measurements data.2013-11-19T00:00:00ZКонструкційна міцність скла та вплив масштабного фактораRodichev, Yu.http://elartu.tntu.edu.ua/handle/123456789/33912018-01-14T09:22:36Z2013-11-19T00:00:00ZНазва: Конструкційна міцність скла та вплив масштабного фактора
Автори: Rodichev, Yu.
Короткий огляд (реферат): Cкло є пружним крихким матеріалом з переважним впливом стану поверхні на
пошкодження, руйнування та міцність елементів при термомеханічному навантаженні. З позицій
континуальної механіки та механіки руйнування розглянуто закономірні особливості конструкційної
міцності листового скла при різних видах напруженого стану. Показано, що опір руйнуванню, міцність і
ресурс скляних елементів, в першу чергу, залежать від структури поверхневого тріщинуватого шару,
який утворюється при виготовленні базового флоат скла, вирізуванні та обробленні деталей і постійно
змінюється під час виготовлення, монтажу та експлуатації конструкцій внаслідок поступового
розсіяного та локалізованого пошкодження і підвищення дефектності поверхні. Встановлено, що
глибина технологічних дефектів, які призводять до зменшення міцності великогабаритних елементів зі
скла, є значно більшою, ніж мікротріщини, що є джерелами руйнування традиційних малих та
стандартних зразків при контрольних випробуваннях міцності будівельного скла. Запропоновано
технічний підхід до експериментального оцінювання конструкційної міцності листового скла з
урахуванням неоднорідності критичних поверхневих дефектів, впливу масштабного та інших
визначальних факторів, який рекомендовано для використання у лабораторних та виробничих умовах
для забезпечення належної міцності та ресурсу великорозмірних будівельних конструкцій. Обгрунтовано
необхідність збільшення довжини зразків флоат скла до 3,2 м та більше, щоб підвищити достовірність
прогнозування міцності та ресурсу великорозмірних будівельних конструкцій. Для оцінювання міцності
скляних балок з вертикальним розташуванням несівних пластин рекомендовано метод випробування
пластин на згин у вертикальному положенні.; Glass is a typical elastic brittle material with a predominant influence of glass surface state
on the damaging, fracture and strength of the elements under thermo-mechanical loading. Basing on the
continual mechanics as well as on fracture mechanics there were analyzed the regularities of a structural
strength for sheet float glass under different modes of stress state. It was shown that fracture resistance,
strength and resource of glass structural elements depend on structure of surface cracked layer first of all. This
layer is formed during the production of float glass, as well as under the glass cutting and machining of the
details. The defects and micro-cracks in this layer are not in the constant state. Their sizes and shapes change
permanently in the result of diffuse and localized damaging of the glass surface under the production and
installation operations, and under the influence of normal and extreme operation conditions. There were
analyzed the experimental methods of structural strength of glass plates evaluation under the bending. The
paper shows the need to consider the influence the size of defects in the surface of samples and components
during mechanical testing of the structural strength of glass. It was obtained that the depth of critical
technological defects, which are typical for large size architectural glass parts is significantly larger than the
depth of cracks formed under processing of conventional small and standard specimens for strength control. So
the results of these specimens’ tests don’t reflect the factual values of building structures made of float glass.The
use of large specimens with a length up to 3.2 m or more for the experimental estimation of surface quality and
the real strength of structural components of sheet float glass is more effective than the use of standard
techniques, which specify the use of small samples. To estimate the strength of glass beams with vertical load-
bearing plates test method with bending the plates in vertical position is recommended. These methods were
proposed for the use at the implementation of complex technical approach for the guaranteeing of required
strength and durability of the architectural glass structures. This technical approach was realized in the building
industry. It includes the special set of the mechanical tests of small specimens and large size samples of glass
with the dimensions comparable with real glass constructions. The full scale experiments on the real building
structures may be made to obtain the important data on surface state, types and sizes of typical damages and
critical parameters of surface micro-cracks. The estimation of real strength level and durability of load-bearing
glass structures was made basing on the results of mechanical tests and micrographs of specimens and
structural elements with a fracture focus analysis. The results may be used for the development of glass
technology and structures optimized basing on strength and durability parameters.2013-11-19T00:00:00ZОцінювання граничного стану моделі колектора пароперегрівника теплової електростанції за підходом R6Бревус, Віталій МиколайовичЯсній, Володимир ПетровичЛапуста, Ю.Yasniy, O.Brevus, V.Yasniy, V.Lapusta, Y.http://elartu.tntu.edu.ua/handle/123456789/33902018-01-11T20:15:49Z2013-11-19T00:00:00ZНазва: Оцінювання граничного стану моделі колектора пароперегрівника теплової електростанції за підходом R6
Автори: Бревус, Віталій Миколайович; Ясній, Володимир Петрович; Лапуста, Ю.; Yasniy, O.; Brevus, V.; Yasniy, V.; Lapusta, Y.
Короткий огляд (реферат): Теплові електростанції (ТЕС) належать до важливих об’єктів, відмови яких можуть
призвести до аварій зі значними наслідками. Більшість ТЕС в Україні вичерпала свій проектний ресурс,
який значною мірою залежить від основних елементів пароводяної системи енергоблоків, що мають
суттєві експлуатаційні пошкодження. Тому важливим завданнями є достовірне оцінювання граничного
стану колекторів пароперегрівників із застосуванням сучасних європейських підходів та врахуванням
експлуатаційної деградації матеріалу.
Колектори пароперегрівників ТЕС експлуатуються у середовищі водяної пари під тиском
15,5 MPa за робочої температури 545 oС. Тривалі термомеханічні напруження, корозійно-наводнене
середовище та сповільнене деформування у цих елементах конструкцій спричиняють появу втомних
тріщин на внутрішній поверхні колектора. Тріщини переважно зароджуються вздовж границь зерен,
ослаблених порами та виділеннями карбідів. Унаслідок експлуатації колекторів змінюються
характеристики механічних властивостей матеріалу.
Оцінено граничний стан моделі колектора пароперегрівника котла ТП-100 з використанням
діаграми оцінювання руйнування (ДОР). ДОР будували для Kmat = KIc та Kmat = Kfc, враховуючи
коефіцієнти запасу міцності для випадку пластичного колапсу та крихкого руйнування моделі колектора
з поперечною тріщиною на внутрішній стінці для різних співвідношень довжини тріщини l до її
глибини a.; Thermal power plants (TPPs) belong to the important objects, the failure of which can cause
accidents with severe consequences. A great part of Ukrainian TPP has exceeded its design life, which is
determined, to large extent, by the main elements of steam power systems. Therefore, the main task is to assess
correctly the superheaters collectors limit state using modern approaches and taking into account the service
degradation of material. TPP superheater collectors operate in the environment of water steam under the
pressure of 15.5 MPa at temperature 545 oC. As a result of combined action of prolonged thermo-mechanical
stresses, corrosive and hydrogen environment and slow deformation, fatigue cracks emerge in these components
on the inner collector surface. Operation of collectors results in the change of the material properties.
The limit state of TP-100 type boiler steam superheater collector model was assessed using failure
assessment diagram (FAD). The FADs were built for Kmat = KIc and Kmat = Kfc. taking into account safety factors
for plastic collapse and for brittle fracture mechanisms for the collector model with part circumferential internal
surface crack for various ratio of crack length l to depth a.
The influence of internal surface crack that is perpendicular to the cylinder axis, on the residual
structural integrity of TPP superheater collector has been studied. The FADss were built taking into account the
fracture toughness of 12Cr1MoV steel after 179 thousand operation hours for static and cyclic loading and,
also, the safety factors for the brittle fracture mechanism and plastic collapse. The critical sizes of the inner
surface defect, that is perpendicular to the axis of the cylinder, considering fracture toughness of 12Cr1MoV
steel for static and cyclic loading, were assessed. It was found out, that with the increase of ratio the minimum
crack depth that is critical for the structural element decreases.2013-11-19T00:00:00ZЗакономірності зміни несучої здатності матеріалу нафтогазопроводів на пізній стадії експлуатаціїСтанецький, Андрій ІгоровичМартинюк, Р.Полутренко, Мирослава СтепанівнаПрисліпська, Галина МиронівнаPoberezhny, L.Pryslipska, G.Stanecky, A.Martynuk, R.Polutrenko, M.http://elartu.tntu.edu.ua/handle/123456789/33892018-01-24T19:40:34Z2013-11-19T00:00:00ZНазва: Закономірності зміни несучої здатності матеріалу нафтогазопроводів на пізній стадії експлуатації
Автори: Станецький, Андрій Ігорович; Мартинюк, Р.; Полутренко, Мирослава Степанівна; Присліпська, Галина Миронівна; Poberezhny, L.; Pryslipska, G.; Stanecky, A.; Martynuk, R.; Polutrenko, M.
Короткий огляд (реферат): Процеси постачання природного газу супроводжуються значними його втратами (у
2001 р. – 1,93 млрд. м3). У зв’язку з цим комплексна проблема мінімізації втрат і підвищення
ефективності використання енергоносіїв є вельми актуальною і її розв’язання дасть змогу зекономити
значні кошти, які можна буде спрямувати на забезпечення безперебійності й надійності постачання
газу споживачу, підтримку належного функціонування газотранспортної системи в цілому. Особливо
важливого значення набувають експериментальні роботи в цьому напрямку, виконані за новими
ефективними методиками, а саме, комплексні дослідження деформівної системи «труба – ґрунтовий
масив» та вивчення кінетики протікання корозійних процесів. З цією метою проведено дослідження
синергічної дії корозійного і механічного чинників на зразках-моделях, вирізаних зі стінки труби.
Об’єктом досліджень вибрано трубопровідну сталь 17Г1СУ, яка є на даний час однією з
найпоширеніших у нафтогазовому комплексі. Для дослідження впливу експлуатаційної деградації було
виготовлено партію зразків з матеріалу труби, яка пробула в експлуатації 41 рік. Встановлено
закономірності зміни несучої здатності матеріалу нафтогазопроводів на пізній стадії експлуатації у
підкислених хлоридних модельних середовищах. Показано, що в кислих грунтових електролітах
деградована трубопровідна сталь має схильність до раптових деформаційних скачків, які можуть
спричинити спонтанну розгерметизацію трубопроводу. Зафіксована деформаційна поведінка сталі
трубопроводу потребує подальшого системного вивчення з метою підвищення рівня безпеки та
забезпечення надійної експлуатації наявних нафто- та газопровідних мереж. У подальшому необхідно
вивчити вплив терміну експлуатації на електрохімічні показники сталей нафтогазового сортаменту з
метою оптимізації параметрів активного та пасивного протикорозійного захисту.; The process of natural gas supply is evidently accompanied with its losses. For instance, there
were lost around 1.93 billion m3 in the year of 2001. Due to this fact, the complex problem of minimizing losses
and improving energy efficiency is urgent and its solution will help to save a lot of money that could be spent on
ensuring continuity and reliability of supply to consumers, as well as to support the proper operation of the gas
transportation system. Relevant experimental works are of great importance, especially those, performed while
employing new effective methods, the comprehensive studies of «pipe – soil array» deformable system and
corrosion processes kinetics in particular. To do this, the corrosion and mechanical synergistic factors action
has been studied on the specimens, cut from the pipe wall. The study of steel deformation behavior under loading
and in the conditions, that are similar to operational, makes possible to estimate the pipeline lifetime, to predict
correctly the operational risks and to estimate the level of potential environmental threats, caused by technical
objects operation. It is important to study the deformation kinetics in corrosive environments, because the
damage level is a result of mechanical and corrosive factors synergistic action, that increases nonlinearly and is
connected with the associated operational risks. The object of study is 17G1S pipeline steel, that is currently one
of the most commonly used in oil and gas industry. To study the impact of operational degradation a set of
samples was machined from the pipeline, that was 41 years under operation. The laws of oil and gas bearing
capacity material changes at the late stage of exploitation in acidified chloride modeling environments were
obtained. It was shown that in acid electrolytes soil the degraded pipe steel has a tendency to sudden
deformation jumps, that can cause spontaneous depressurization of the pipeline. The observed steel pipeline
system deformation behavior needs further study to ensure existing oil and gas pipeline networks safety and
reliable operation. Further, it is necessary to study the effect of lifetime on the steel oil and gas electrochemical
properties in order to optimize the parameters of active and passive corrosion protection.2013-11-19T00:00:00ZОценка достоверности контроля трещин в авиационных конструкцияхБурау, Н.Хумарян, Л.Ignatovich, S.Bouraou, N.Khumarian, L.http://elartu.tntu.edu.ua/handle/123456789/33882018-01-23T22:11:50Z2013-11-19T00:00:00ZНазва: Оценка достоверности контроля трещин в авиационных конструкциях
Автори: Бурау, Н.; Хумарян, Л.; Ignatovich, S.; Bouraou, N.; Khumarian, L.
Короткий огляд (реферат): Достоверность обнаружения трещин методами неразрушающего контроля (НК)
определяется вероятностью обнаружения дефекта с заданным размером а – POD(a). Показано, что
этот показатель определяет надежность всей системы НК, включая человеческий фактор. На примере
использования вероятностного подхода Бейеса с учетом POD(a) показана возможность некорректного
обоснования эмпирического распределения размера дефектов.; The realization of the damage tolerance concept for aviation structures is defined appreciably
by solution of a problem of the damage detection reliability by nondestructive inspection (NDI) methods. The
reliability of cracks detection by NDI methods is defined by probability of detection of the given flow size a –
POD (a). The reliability index of the NDI taking into account the reliability of the flow detection or miss POD
(a) is the probability of the crack size detection more than a. Another reliability index of the NDI system, which
depends on POD (a), is the missing probability of the crack size more than a. It is shown that POD (a) defines
reliability of all NDI system, including the human factor. The example of a wing surface control by eddy currents
is considered for the plane round rivet holes in knots of skin and stringer fastening. The distribution of the
detected crack length is described by a Weibull distribution (a posteriori distribution). However, this distribution
cannot be accepted as correct because the part of cracks will be not detect under control (especially small sizes
cracks). It is shown that a priori (valid) crack length distribution can be defined by using of the Bayesian
probabilistic approach, which essentially differs from initial Weibull distribution. The approach offered in this
paper is useful to an estimation of a technical condition of aircraft structures by results of operation defects
testing.2013-11-19T00:00:00ZМоделювання континуального руйнування просторових тіл в умовах тривалого статичного і циклічного навантаженняГуляр, Олександр ІвановичПискунов, С.Bazhenov, V.Gulyar, O.Pyskunov, S.http://elartu.tntu.edu.ua/handle/123456789/33872018-01-23T19:15:41Z2013-11-19T00:00:00ZНазва: Моделювання континуального руйнування просторових тіл в умовах тривалого статичного і циклічного навантаження
Автори: Гуляр, Олександр Іванович; Пискунов, С.; Bazhenov, V.; Gulyar, O.; Pyskunov, S.
Короткий огляд (реферат): Представлено методику моделювання процесів континуального руйнування кругових та
призматичних тіл складної форми в умовах тривалого статичного і багатоциклового навантаження:
скінчено-елементна база для визначення напружено-деформованого стану просторових тіл на основі
напіваналітичного методу скінчених елементів (НМСЕ), алгоритми визначення феноменологічного
параметра пошкодженості та моделювання еволюційних процесів розповсюдження зон континуального
руйнування. Наведено результати розв’язання практичних задач із визначення розрахункового і
додаткового ресурсу відповідальних просторових об’єктів.; Techniques of continual fracture process modelling of complex shape circular and prismatic
bodies under elastic high-cycle deformation and in condition of creep under prolonged static load is presented
in this paper. The semianalytic finite element method (SFEM) to determine the stress-strain state is used. SFEM
involves the application of finite element mesh in the cross section of the body, and using one finite element in
the direction of straight or curved creating, which provides significantly lower computational cost for three-
dimensional problems solving. The Kachanov-Rabotnov’s scalar damage parameter to describe the continual
fracture of the material and the degree dependence of the damage parameter accumulation rate of on the stress
state parameters are used. Stepping algorithms for the stress-strain state and damage parameter determining for
considered deformation process have been developed. The algorithm of simulation of evolutionary processes of
macroscopic defects (continual fracture zone) growth after local loss of material bearing capacity because of
damage parameter’s critical value has been obtained. A solution of practical problems of determining of the
calculated lifetime (to local loss of material bearing capacity) and the additional lifetime (time of continual
fracture zone growth) for high pressure connecting pipe and the gas turbine blade has been presented. It is
shown, that for the connecting pipe which represents thick-wall rotation body, lifetime is not limited to local loss
of material bearing capacity and can be significantly extended by additional lifetime. At the same time for the
blade under creep condition lifetime is completely determined by the local loss of material bearing capacity,
because the value of additional lifetime is related to the continual fracture zone growth of only about 5% of the
calculated lifetime.2013-11-19T00:00:00ZВизначення кінетики втомного пошкодження й довговічності сталей в умовах неоднорідного напружено-деформованого стануНовіков, Анатолій ОлександровичTsyban, G.Novikov, A.http://elartu.tntu.edu.ua/handle/123456789/33862018-01-24T07:31:35Z2013-11-19T00:00:00ZНазва: Визначення кінетики втомного пошкодження й довговічності сталей в умовах неоднорідного напружено-деформованого стану
Автори: Новіков, Анатолій Олександрович; Tsyban, G.; Novikov, A.
Короткий огляд (реферат): Описано основні рівняння моделі граничного вичерпання циклічної пластичності,
конкретизацію її функцій і наповнення граничними параметрами. Далі на базі цієї моделі розроблено
підхід до розрахунку довговічності елементів конструкцій у пружно-пластичній постановці. Підхід
використано для знаходження втомної довговічності призматичних зразків при симетричному
циклічному згині за даними, отриманими при симетричному розтягу-стиску. Розрахунки дозволяють
побудувати епюри напружено-деформованого стану і втомного пошкодження при циклічному згині, а
також їх кінетику. Для цього, за розробленою моделлю, пошкодження й вичерпання пластичності
визначається покроково для тонких шарів матеріалу з необхідним кроком їх дискретизації. Розрахунки
довговічності елементів конструкцій з градієнтом напружень проводяться за критерієм зародження
короткої тріщини заданого розміру.; The paper presents the basic equations for the model of ultimate cycle plasticity exhaustion,
refinement of its functions and introduction of boundary conditions. The paper presents the generalized
experimental results on high-cycle fatigue and inelastic deformation of 15 structural materials of different
classes. The cyclic stress-strain curve equation, which describes the evolution of the elastoplastic behavior of the
material from the beginning of loading up to fracture over the entire range of high-cycle fatigue, is proposed.
Basing on this model an approach to calculation of the durability of structural elements in elastoplastic
formulation has been developed. A numerical-analytical solution of the problem on distribution diagram of the
elastoplastic stress-strain state in cyclic bending has been obtained for the material, which changes its
elastoplastic properties with the increase of the operation time. The software algorithms have been developed
and implemented for computational fatigue curve plotting under strain-controlled loading as well as under
conditions of nonuniform stress-strain state. This approach is used to determine the fatigue life of prismatic
specimens subjected to symmetrical cyclic bending using the data obtained under symmetric tension-
compression. The results of calculations make it possible to build the distribution diagrams of stress-strain state
and fatigue damage as well as their kinetics under cyclic bending. For this purpose damage and exhaustion of
plasticity are determined stepwise for thin layers of the material with a required discretization interval. The
calculations of durability of structural elements with stress gradient are conducted by the certain size crack
initiation criterion. It is justified that accounting for the kinetics of inelastic strains under conditions of
nonuniform stress-strain state makes it possible to describe the difference in fatigue damage accumulation for
hardening and softening materials. Calculations similar to those presented in the paper can also be made for
structural elements with stress concentrators.2013-11-19T00:00:00ZИспользование деформационного критерия трещиностойкости для оценивания остаточного ресурса труб линейной части нефтепроводаБогданович, А.Веселуха, В.Воробьёв, В.Козик, А.Sosnovskiy, L.Bogdanovich, A.Veselykha, V.Vorob, V.Kozik, A.http://elartu.tntu.edu.ua/handle/123456789/33852018-01-11T19:31:32Z2013-11-19T00:00:00ZНазва: Использование деформационного критерия трещиностойкости для оценивания остаточного ресурса труб линейной части нефтепровода
Автори: Богданович, А.; Веселуха, В.; Воробьёв, В.; Козик, А.; Sosnovskiy, L.; Bogdanovich, A.; Veselykha, V.; Vorob, V.; Kozik, A.
Короткий огляд (реферат): Для оценивания трещиностойкости труб, изготовленных из пластичной стали,
использовать подходы линейной механики разрушения проблематично ввиду несоблюдения условий
плоской деформации. Один из вариантов решения проблемы состоит в экстраполяции формул линейной
механики разрушения для коэффициента интенсивности напряжений (КИН) на существенно
нелинейную стадию деформирования с помощью функций поправки на пластичность. В работе
анализируются результаты испытаний на циклическую трещиностойкость образцов из трубной стали
на основе нового инженерного подхода. Получены силовые и деформационные характеристики
трещиностойкости исследуемой стали. Дан анализ построенных кинетических диаграмм усталостного
разрушения и диаграмм циклического упругопластического разрушения образцов, живучести труб из
исследованной стали после длительной эксплуатации.; To estimate the crack growth resistance of pipes made of ductile steel using a linear fracture
mechanics approach is of problematic character as the conditions of plane strain are not observed. One of the
ways of solution to the problem is the extrapolation of the linear fracture mechanics formulas for the stress
intensity factor (SIF) on substantially nonlinear stage of deformation by means of the amendment functions on
the plasticity.
The results of crack growth resistance tests of samples made of pipe steel on the basis of a new
engineering approach are analyzed in the paper. The force and deformation characteristics of the crack growth
resistance were received.
The analysis of kinetic fatigue failure diagrams and cyclic elastic-plastic fracture diagrams for
specimens, crack growth life of tubes from the investigated steel after long-term use is presented.
Specimen’s crack is oriented in axial and circumferential directions for study of anisotropy properties.
The characteristics of a fatigue crack growth of investigated steel after long operation are discussed. The
characteristics of cyclic crack growth resistance for pipe steel after long-term (over 30 years) of operation are
determined experimentally: at absolute temperature T = 293 K and a critical threshold values of SIF are: Kth =
4,91 MPa, Kfc = 54,75 MPa, the values parameters of equation (6) are equal mk = 1,556, Ck = 4,0 ⋅ 10 −10.
The algorithm and procedure of computational experimental evaluation of crack growth life of objects
operated under cyclic elastic-plastic deformation, which is based on the use of strain approach - measuring of
specimen’s width reduction, charting the cyclic elastic-plastic fracture diagram, for practical application are
proposed. Graphical analysis of data according to crack growth life and service term of the tube of oil pipe line
with a semi-elliptical longitudinal crack from damage is presented at various levels of pressure in the tube: 1, 2
and 3 MPa.2013-11-19T00:00:00ZСтруктурно-функціональний синтез систем діагностики конструкцій в експлуатаціїПавловський, О.Шевчук, Д.Bouraou, N.Pavlovskyi, O.Shevchuk, D.http://elartu.tntu.edu.ua/handle/123456789/33842018-01-11T19:31:23Z2013-11-19T00:00:00ZНазва: Структурно-функціональний синтез систем діагностики конструкцій в експлуатації
Автори: Павловський, О.; Шевчук, Д.; Bouraou, N.; Pavlovskyi, O.; Shevchuk, D.
Короткий огляд (реферат): Розглянуто основи синтезу нового класу діагностичних систем – комплексних
інтелектуальних систем моніторингу технічного стану конструкцій в експлуатації. За принципом
побудови та функціонування такі системи відносяться до систем, що реалізують сучасну концепцію
Structural Health Monitoring. Метою структурно-функціонального синтезу системи є формування
мережі вимірювальних каналів та оптимізація структури системи для своєчасного безпомилкового
визначення поточного технічного стану об’єкта контролю та прогнозування його майбутніх станів.
Вибір та оптимізація структури визначаються поставленою діагностичною метою та апріорними
даними про досліджувані фізичні процеси з урахуванням інформаційних аспектів процесів
діагностування, які реалізуються в системі. Розглянуто й проаналізовано узагальнену функціональну
блок-схему системи, узагальнену схему передавання інформації, розглянуто деякі типи датчиків
первинної інформації, які можуть бути використані в системі. Як приклад, наведено функціональну
схему системи моніторингу для попередження руйнування резервуарів з еколого-небезпечними
речовинами, які знаходяться у важкодоступних місцях та під впливом динамічних і кліматичних
навантажень.; Bases of synthesis of the new class of diagnostic systems – the complex smart systems of
monitoring of a technical condition of construction at the operating are observed. According to the construction
and operation principles such systems refer to systems, which realize the modern concept Structural Health
Monitoring. The purposes of a structural functional synthesis of the system are formation of a network of
measuring channels, optimization of structure of system for timely and correct determination of a current
technical condition of the testing object, and prediction of its future conditions. Choice and optimization of
structure of the system are defined by the formulated diagnostic aim, the previous data on the investigated
physical processes taking into account the informational aspects of diagnostic processes, which are realized in
the system. Monitoring system measuring channels contain the source of information sensing transducers,
converters, amplifiers, filters, communication lines. Requirements are listed for choice and optimization of
types and quantity of the monitoring system measuring channels. The generalized functional block diagram of
the monitoring system and the generalized diagram of information transfer are observed and analyzed. Some
types of sensing transducers of a source information are observed, which can be used in monitoring systems.
These are sensing transducers of acoustical emission, sensing transducers of vibration and fiber-optical
displacement sensors. The choice of types of the sensing transducers is defined by the following factors:
sensitivity, accuracy, weight and dimensional characteristics, efficiency of the realized method of non-
destructive testing, as well as specificity of the testing object. The functional diagram of the monitoring system
are presented for the preventing of destruction of tanks with ecology-dangerous substances, which are located in
hard-to-reach spots, and are under the influence of dynamic and climatic loadings.2013-11-19T00:00:00ZПро контактну задачу для циліндричного штампа і шару з початковими (залишковими) напруженнямиIaretska, N.http://elartu.tntu.edu.ua/handle/123456789/33832018-01-11T19:27:35Z2013-11-19T00:00:00ZНазва: Про контактну задачу для циліндричного штампа і шару з початковими (залишковими) напруженнями
Автори: Iaretska, N.
Короткий огляд (реферат): У рамках лінеаризованної теорїї пружності представлена осесиметрична змішана задача про тиск пружного циліндричного
штампу на шар з початковими (залишковими) напруженнями. Дослідження представлені в загальному
вигляді для теорії великих початкових деформацій та різних варіантів теорії малих початкових
деформацій при довільній структурі пружного потенціалу.; The article deals with the coaxial mixed type task of measuring pressure of an elastic cylinder
punch upon a layer with initial (residual) stresses within the framework of linear elasticity theory. Two cases
will be viewed in the article 1) the layer is placed on an elastic surface without frictioning; 2) the layer is
fastened to an elastic surface. In general, the research was carried out for the theory of great initial (ultimate)
deformations and different variants of the theory of small initial deformations with arbitrary structure of elastic
potential. It is assumed that elastic potentials are two continuously differentiated functions of algebraic
invariants of the Green tensor deformation (the initial states of the layer and of the cylindrical punch remains
uniform and equal). The research is carried out within the coordinates of the initial deformed state, which are
interrelated with the Lagrangian coordinates (natural state). Besides, it is also assumed that the influence of the
die causes small disorders of the main elastic deformed state.
It is assumed that the elastic die as well as the layer are made of different isotropous, transversely
isotropic or composite materials and they are interacting on one of the die’s surfaces.
The mode of deformation in elastic layer with initial (residual) stress will be defined with the help of
harmonic functions as the Henkel integrals. We should note, although the Henkel-method does not provide exact
solutions, but it lets us reduce the task to the Fredholm equations, which let us use the method of consecutive
approximations. Consequently we got a components of potential vector and tenzor of deformations in the case of
unequal roots of axis-symetrical type task.
So, the received solutions are defined by lines with the help of very many constants. These constants are
defined with regular and linear algebraic systems. The research was carried out on the problem of the influence
of initial stresses on the law of distribution of contact disorders in the elastic layer with initial (residual)
stresses.
The article deals with the coaxial mixed type task of measuring pressure of an elastic cylinder die upon a
layer with initial stresses within the framework of linear elasticity theory. In general, the research was carried
out for the theory of great initial (ultimate) deformations and different variants of the theory of small initial
deformations with arbitrary structure of elastic potential.2013-11-19T00:00:00ZНапружено-деформований стан ортотропної пружно-пластичної замкненої циліндричної оболонки з внутрішньою поздовжньою тріщиною довільної конфігураціїПороховський, Юрій ВасиловичNykolyshyn, T.Porokhovs, Yu.http://elartu.tntu.edu.ua/handle/123456789/33822018-01-11T19:31:51Z2013-11-19T00:00:00ZНазва: Напружено-деформований стан ортотропної пружно-пластичної замкненої циліндричної оболонки з внутрішньою поздовжньою тріщиною довільної конфігурації
Автори: Пороховський, Юрій Василович; Nykolyshyn, T.; Porokhovs, Yu.
Короткий огляд (реферат): Задачу про напружений стан і граничну рівновагу циліндричної ортотропної оболонки з
внутрішньою тріщиною довільної конфігурації зведено до системи нелінійних сингулярних інтегральних
рівнянь. Запропоновано алгоритм числового розв’язання отриманої системи. Вивчено вплив ортотропії,
навантаження та геометричних параметрів на розкриття тріщини і розміри пластичних зон поблизу
неї.; The strength of real solids is determined not only by their physical and chemical nature, but
also depends significantly on the defectiveness of their structure. The solving of the problem on fracture of
materials can be successful only in the case of accounting the defects contained in the body, as well as structural
cuts and inclusions. During the deformation of the solid body in the vicinity of such concentrators high stress
intensity occurs, which leads to the yielding flow of the material, to cracks initiation and propagation, i.e. to a
local or complete fracture of the body [1, 2].
To evaluate the effect of different types of defects on the stress state and the limit equilibrium of the body,
it is advisable to perform an investigation of stress concentrators that are subject to analytical study. Such stress
concentrators, for example, in thin-walled structures are through and internal cracks.
The anisotropic closed cylindrical elastic-plastic shell, weakened by internal cracks of arbitrary
configuration is studied.
The three-dimensional elastic-plastic problem on the stressed state and limiting equilibrium of closed
orthotropic cylindrical shell with inner longitudinal crack of arbitrary configuration using analogue of the δc-
model is reduced to a two-dimensional problem on elastic equilibrium of the same shell with a through crack of
unknown length, and the last problem (in the refined Timoshenko-type shell theory) is reduced to the tenth order
system of five key differential equations with unknown boundaries of integration and discontinuous functions in
the right-hand side containing the unknown values.
Using the fundamental solution and operation of convolution the integral representations of key functions
of forces and moments for the closed orthotropic cylindrical shell are constructed, which, in turn, are reduced to
the system of two singular integral equations.
The algorithm for the numerical solution of the obtained system together with the conditions of plasticity
of thin shells, with conditions of the uniqueness of displacements and conditions of boundedness of forces and
moments in the vicinity of the crack is proposed. This algorithm is implemented for the case of a parabolic
crack. The numerical analysis of dependence of crack opening displacements and sizes of the plastic zone is
carried out for shells made from such materials: a composite material on epoxy basis reinforced by
unidirectional graphite fibers, composite material on epoxy basis reinforced by unidirectional fibers of S-glass;
bor-epoxy composite. The comparison of obtained results with the results for the corresponding rectangular
internal crack, bounded by lines parallel to the coordinate lines is given.2013-11-19T00:00:00ZОдновісний розтяг пружно-пластичних пластин з квадратним отвором різної орієнтаціїКуз, О.Kuz, I.Kuz, O.http://elartu.tntu.edu.ua/handle/123456789/33812018-01-11T19:57:21Z2013-11-19T00:00:00ZНазва: Одновісний розтяг пружно-пластичних пластин з квадратним отвором різної орієнтації
Автори: Куз, О.; Kuz, I.; Kuz, O.
Короткий огляд (реферат): На основі числового розв’язування крайових задач теорії малих пружно-пластичних
деформацій для лінійно зміцнюваного матеріалу з урахуванням розвантаження з’ясовано вплив
орієнтації квадратного отвору в пластині на її напружено-деформований стан за одновісного розтягу.; Effective numerical methods for solving 2D problems related to the theories of elasticity and
plasticity have been worked out. The variation-difference method of building finite difference schemes is
extended to domains with curvilinear boundaries and disconnected domains.
The application of the variation-difference method for solving problems of the theory of small elasto-
plastic deformations relatively the plates with a hole, taking into account the linear strengthening of the material
and unloading, has been developed. For solving the resultant systems of nonlinear and linear equation, the
Newton-Kantorovich method and combined iterative method (gradient and cyclic Chebyshev’s one) were
proposed to be used. The choice of iteration parameters of the methods for solving the obtained systems of linear
and nonlinear algebraic equations was made.
The elaborated software ensures solving the problems with different boundary conditions, medium and
domain parameters.
A variety of problems concerning one-axis stretching of the plates with the square hole of different
orientation relatively the axis of stretching is numerically solved. The zones of evolution of plastic deformations
for step enlarging of the loading are constructed, the remaining deformations and the limit loads are obtained.
The influence of the orientation of square hole in the plate onto the stress magnitude was found. The
orientation of the hole does not make essential influence onto the shape of zones of generation and development
of residual deformations, but it essentially impacts onto magnitudes of the components of the stress tensor and
its intensity, and therefore the moment of the beginning of plastic deformation. That is, in a plate with rotated
square hole the initial plastic deformations appear under the tension 45% less than in a non-rotated one.2013-11-19T00:00:00ZСистема крайових паралельних тріщин у зоні контакту тіл коченняДацишин, О.Levus, A.Datsyshyn, O.http://elartu.tntu.edu.ua/handle/123456789/33802018-01-11T19:57:28Z2013-11-19T00:00:00ZНазва: Система крайових паралельних тріщин у зоні контакту тіл кочення
Автори: Дацишин, О.; Levus, A.; Datsyshyn, O.
Короткий огляд (реферат): Записано сингулярні інтегральні рівняння для системи крайових паралельних нерівних
нахилених тріщин у пружній півплощині, береги яких контактують без тертя під час переміщення
герцівського навантаження вздовж краю півплощини. Запропоновано алгоритм визначення меж ділянок
контактування берегів тріщин та коефіцієнтів інтенсивності напружень у їх вершинах. Числові
результати отримано для випадку двох паралельних рівних тріщин.; The surface (edge) parallel cracks system is one of typical contact fatigue damages of
elements of wheel-rail technical pair. So, the important task for estimation of a contact strength and durability of
such pair is determination of a stress-strain state or stress intensity factors (SIF) at crack tips under operational
conditions.
In given investigation the model scheme, where in a two-dimensional case damaged bodies are simulated
by elastic halfplane with cuts, and counterbody action by forward unidirectional movement of model contact
load along halfplane boundary, has been used for simulation of contact rolling interaction. Other parameters
have been chosen according to operational conditions for wheel-rail pair and typical features of damages.
Singular integral equations of contact problem of elasticity theory for halfplane with the system of
parallel inclined cracks, the faces of which are in contact without friction under action of a moving model load
(Hertzian pressure with tangential component) have been constructed. The algorithm (iterative procedure) for
finding of opened segments of a cracks faces has been developed. Numerical results for the case of two equal
parallel cracks, inclined at angle β = 5π/6 to direction of a tangential contact efforts and, respectively, at angle
π –β = 30° to direction of a counterbody movement for different values of a friction coefficient (f = 0.1 and
f = 0.3) in a contact between rolling bodies and different relative distances between cracks δ = b/a depending
on a contact load position in relation to cracks have been obtained. The maps of cracks faces contacting during
a contact load movement along halfplane boundary (change of parameter λ = х0/а) have been constructed and
stress intensity factors KI, KII and mixed SIF KIθ have been calculated.
It was determined that cracks begin to close mainly from the mouth during contact load movement.
The value of ∆KII = maxKII(λ) – minKII(λ) parameter, that controls the fracture by shear mechanism
significantly depends on a distance between the cracks and a substantial weakening of rolling body nearsurface
area (maximum of ∆KII) is achieved under distance, that commensurable with the contact segment length.
Maximum and minimum of KII(λ) are realized if both cracks are contacting along all its length. So, partial
opening of cracks has little influence on ∆KII range.
The analysis of K I∗θ = max K Iθ (λ , θ ) parameter, that controls the fracture by opening mechanism,
showed: when the contact load is directly above the crack(s) not only shear fracture can occur, but fracture by
opening can occur too.
Generally, the presence of a fully closed crack with contacting faces can significantly influence the SIF of
another opened crack. Therefore, this influence can not be neglected.2013-11-19T00:00:00ZКорозійна деградація сталей сітчастих гіперболоїдних конструкційКутний, А.Никифорчин, Григорій МиколайовичZvirko, O.Kutnyi, A.Nykyforchyn, H.http://elartu.tntu.edu.ua/handle/123456789/33792018-01-23T19:15:59Z2013-11-19T00:00:00ZНазва: Корозійна деградація сталей сітчастих гіперболоїдних конструкцій
Автори: Кутний, А.; Никифорчин, Григорій Миколайович; Zvirko, O.; Kutnyi, A.; Nykyforchyn, H.
Короткий огляд (реферат): Досліджено корозійну тривкість та електрохімічну поведінку вуглецевих сталей
експлуатованих понад 100 років сітчастих гіперболоїдних конструкцій (веж Шухова) та сучасної
вуглецевої сталі у вихідному стані у 0,3% водному розчині NaCl. Встановлено, що вуглецева сталь
Аджигольського маяка характеризується нижчою корозійною тривкістю порівняно з сучасною
вуглецевою сталлю у вихідному стані та вуглецевою сталлю водонапірної вежі у Черкасах, що зумовлено
тривалим впливом агресивного корозивного наводнювального середовища. Виявлено погіршення низки
корозійно-електрохімічних характеристик сталі маяка внаслідок її експлуатаційної деградації –
стаціонарного потенціалу, густини струму корозії та поляризаційного опору, які можуть виступати
достатньо чутливими інформаційними ознаками експлуатаційної деградації сталі.; A number of unique engineering monuments – the lattice towers created by outstanding
engineer V.G. Shukhov have been preserved in Ukraine. Atmospheric corrosion is the main reason of the
deterioration of their performance because the towers are made of carbon steel, which has insufficient corrosion
resistance and they are not properly protected against corrosion. Therefore, the expertise of constructions
corrosion damages, the establishment of corrosion peculiarities, the use of modern corrosion protection and
corrosion monitoring are necessary for their conservation.
The paper is devoted to studying the influence of long-term operation on corrosion resistance and
electrochemical behavior of carbon steels of lattice hyperboloid towers in comparison with modern carbon steel
in the initial state and detecting the informative features, which are sensitive to a change of a metal state due to
long-term operation.
The corrosion resistance and electrochemical behavior of carbon steels of the 100-year-old Shukhov
lattice towers and modern carbon steel in the initial state in 0.3% NaCl aqueous solution have been investigated.
It has been established that the Adziogol Lighthouse carbon steel is characterized by the reduced corrosion resistance in
comparison with the modern carbon steel in the initial state and the carbon steel of the Cherkasy water tower
which is likely to be caused by long-term exposure to aggressive corrosive and hydrogenating environment. The
deterioration of corrosion and electrochemical properties of lighthouse steel, such as stationary potential,
corrosion current density and polarization resistance, due to its exploited degradation has been found. These
characteristics may be enough informative features of the in-service steel degradation. To maintain a
conservation of the lattice tower constructions it is necessary to provide its effective corrosion protection using
modern technology.2013-11-19T00:00:00ZВплив частоти та асиметрії циклу навантаження на швидкість поширення корозійно-втомних тріщинДмитрах, І.Syrotyuk, A.Dmytrakh, I.http://elartu.tntu.edu.ua/handle/123456789/33782018-01-05T11:29:45Z2013-11-19T00:00:00ZНазва: Вплив частоти та асиметрії циклу навантаження на швидкість поширення корозійно-втомних тріщин
Автори: Дмитрах, І.; Syrotyuk, A.; Dmytrakh, I.
Короткий огляд (реферат): Побудовано базові діаграми циклічної корозійної тріщиностійкості конструкційних
сталей 20, 12Х1МФ та 08Х18Н12Т, які є основою для проведення розрахунків на довговічність, а також
відображають вплив частоти й асиметрії циклу навантаження на швидкість поширення корозійно-
втомних тріщин. Для досліджених сталей встановлено екстремальні значення частоти навантаження
f = f ∗ , тобто такі, коли проявляється максимальний вплив корозивного середовища на ріст корозійно-
втомних тріщин. Показано, що зі зростанням коефіцієнта асиметрії циклу від R = 0 до R = 0, 7 для всіх
сталей суттєво знижуються характеристики циклічної корозійної тріщиностійкості. При цьому
діаграми їх циклічної корозійної тріщиностійкості зміщуються в область менших значень ∆K , а
також стають більш стрімкішими. Враховуючи спектр отриманих експериментальних даних, можна
стверджувати, що використання методів механіки руйнування і, зокрема, характеристик
тріщиностійкості матеріалів для оцінювання та прогнозування залишкового ресурсу елементів
різноманітних відповідальних конструкцій дасть можливість не тільки здійснити принципово якісні
зміни в підходах до вирішення цієї проблеми, але й сприятиме зближенню вітчизняної нормативної бази
з міжнародною.; Based on the results of experimental tests the corrosion fatigue crack growth diagrams for
steels 20, 12Х1МФ and 08Х18Н12Т were constructed, which are the base for durability calculation of structural
components. These diagrams also reflect the influence of frequency and stress ration of loading cycle on fatigue
cracks propagation under presence of corrosive operating environment.
The frequency of cyclic loading defines the development of fatigue cracks in structural steels under
conditions of corrosive-aggressive environments inasmuch as effects on the time of interaction of corrosion
environment with the deformed metal at the pre-fracture zone of material. For studied steels the characteristic
values of frequency of loading f = f ∗ were found, when the maximal environmental effect on corrosion fatigue
crack growth rate is achieved. Such extreme on frequency dependence is associated with the ratio of rates of the
electrochemical reactions flow in the vicinity the crack tip and the formation of new electrochemically active
surface due to crack propagation. These data should be used under construction of the basic corrosion fatigue
crack growth diagrams, which are intended for further calculation of durability of defected structural elements.
Based on the test results it has been shown that with the increase of stress ration from R = 0 to R = 0.7
the crack growth resistance of given steels decreases significantly. Under the corrosion fatigue crack growth
diagrams shift to the range of lower values of ∆K and their slope increases. Presented results testified the
necessity to take into account the effects of the stress ratio under construction of basic diagrams of corrosion
fatigue crack growth resistance for durability calculation.
Taking into account the received spectrum of the experimental data it can be stated that application of
fracture mechanics methods as well as characteristics of fatigue growth resistance for the assessment of residual
lifetime of different structural elements gives the possibility to make the essentially qualitative changes in
approaches for solution of this problem and also to converge the national codes with international.2013-11-19T00:00:00ZРозрахунки динамічних коефіцієнтів інтенсивності напружень у пружних двовимірних тілах з криволінійними тріщинамиКравець, В.Savruk, M.Kravets, V.http://elartu.tntu.edu.ua/handle/123456789/33772018-01-11T19:57:08Z2013-11-19T00:00:00ZНазва: Розрахунки динамічних коефіцієнтів інтенсивності напружень у пружних двовимірних тілах з криволінійними тріщинами
Автори: Кравець, В.; Savruk, M.; Kravets, V.
Короткий огляд (реферат): Розв’язано плоскі динамічні задачі теорії пружності для тіл з гладкими криволінійними
тріщинами, на берегах яких діють нормальні та дотичні динамічні навантаження. Застосовано
модифікований метод скінченних різниць за часом у поєднанні з методом сингулярних інтегро-
диференційних рівнянь за просторовими змінними. Використовуючи фундаментальний розв’язок рівнянь
Гельмгольца для плоских задач динамічної теорії пружності, побудовано інтегральні зображення
хвильових потенціалів. На їх основі крайову задачу для гладких криволінійних тріщин зведено до
послідовного (у кожен вузловий момент часу) розв’язування сингулярних інтегро-диференційних рівнянь.
Числові розв’язки інтегральних рівнянь отримано методом механічних квадратур. Обчислено динамічні
коефіцієнти інтенсивності напружень для криволінійних тріщин по дугах кола, параболи та півеліпса за
нормальних та дотичних ударних навантажень на їх берегах. Проаналізовано вплив форми та кривини
контурів тріщини на зміну поведінки коефіцієнтів інтенсивності напружень у часі.; A solution method for the dynamic problems of elasticity theory for infinity bodies with smooth
curvilinear cracks is developed. The plane dynamic problems of elasticity theory for bodies with smooth
curvilinear cracks are solved for the case of normal and tangential dynamic loads at the crack faces. A modified
finite difference method with respect to the time variable only in combination with the method of singular
integral-differential equations for the space variables is applied. For zero initial conditions the equations of
motion are reduced to homogeneous systems of differential equations for determination of displacements at fixed
time nodes. For the two-dimensional dynamic problems of the crack theory the efficient solution of these
differential equations is obtained by the boundary integral equation method. Using the fundamental solution of
the Helmholtz equation for plane problems of elasticity theory the integral representation of the wave potential
is built. On this basis the boundary problem for the smooth curvilinear cracks is reduced to the step by step (with
respect to the nodal points of time) solution of the singular integral-differential equations.
Numerical solutions of this integral equations are obtained by the method of mechanical quadratures.
The direct approach to the method of mechanical quadratures for numerical solution of integral-differential
equations, in which kernels along with regular components contain singularity of Cauchy and logarithmic
singularity was used. This approach allows to use the standard quadrature formulas to calculate the integrals at
the unclosed contours without extracting singularities in the integrand kernels.
The dynamic stress intensity factors are computed for curved cracks of different configurations (circular,
parabolic and semielliptic arcs) for normal and shear impact loads on their faces. The influence of the shape
and curvature contours of the crack on the behavior of stress intensity factors in time is analyzed. It was found
that the main influence on the behavior of dynamic stress intensity factors is not the relative deflection of the
crack contour and its form – especially in the vicinity of the crack tips. In particular cases of the uniformly
distributed normal or shear impact loadings at the rectilinear crack faces our results are consistent with the
data obtained by the other methods.2013-11-19T00:00:00ZВплив водню на ріст повзучо-втомних тріщин у тонкостінних елементах конструкційДобровольська, Л.Долінська, Ірина ЯрославівнаЯворська, Н.Andreykiv, O.Dolinska, I.Yavorska, N.Dobrovolska, L.http://elartu.tntu.edu.ua/handle/123456789/33752018-01-24T07:31:03Z2013-11-19T00:00:00ZНазва: Вплив водню на ріст повзучо-втомних тріщин у тонкостінних елементах конструкцій
Автори: Добровольська, Л.; Долінська, Ірина Ярославівна; Яворська, Н.; Andreykiv, O.; Dolinska, I.; Yavorska, N.; Dobrovolska, L.
Короткий огляд (реферат): Побудовано математичну модель для визначення впливу водню на ріст повзучо-втомних
тріщин у тонкостінних елементах конструкцій за змінних у часі навантажень і високих температур.
На основі цього досліджено відповідний аналог задачі Гріффітса, де встановлено, що неврахування
впливу водню у докритичному рості повзучо-втомної тріщини може призвести до переоцінювання
залишкової довговічності пластини і до непередбачуваного руйнування.; The mathematical model for determination of influence of hydrogen on the creep-fatigue crack
growth in thin-walled structural elements under the variable in time loading and high temperatures has been
built. (Temperature of structural elements is higher than half melting points of material. This temperature will
facilitate emergence of high-temperature creep in the plastic zone near the crack tip). It is based on the first law
of thermodynamics concerning mechanics of solid slow fracture at high temperature creep, variable loading and
environment containing hydrogen. It is assumed, that the period of unsteady creep dominates here. In this case
the main mechanism of fracture is creep-fatigue fracture and hydrogen only intensifies or weakens this process.
We assume that crack propagation occurs by jumps during incubation periods of high temperature creep in the
prefracture zone near the crack tip. Then the crack growth rate can be represented as the average ratio of the
length and its jump to the time of incubation period. Considering this and equation the rate of change of energy
balance an equation to determine the growth rate of creep-fatigue macrocrack is obtained. This equation with
the initial and final conditions is a mathematical model for determining the period of subcritical creep-fatigue
crack growth in terms of environment containing hydrogen. On this basis the influence of hydrogen on the
residual life-time of thin-walled plate made of steel 321 with a straight crack (analogue of Griffiths problem)
under cyclic loads and high-temperature creep was determined. The dependence of the residual life-time of the
plate on the initial defect size for the cases of account and not account operating on plate environment
containing hydrogen has been graphically constructed. It is shown that the hydrogen increases of creep-fatigue
crack propagation rate, which reduces the life-time of the plate. So ignoring of influence of hydrogen in the
subcritical of creep-fatigue crack can result in revaluation of residual life-time of the plate and not to predict
fracture.2013-11-19T00:00:00ZТитулhttp://elartu.tntu.edu.ua/handle/123456789/33732018-01-11T19:39:23Z2013-11-19T00:00:00ZНазва: Титул2013-11-19T00:00:00ZПам’яті професора М.П. Ленюкаhttp://elartu.tntu.edu.ua/handle/123456789/34092018-01-11T19:57:32Z2013-11-19T00:00:00ZНазва: Пам’яті професора М.П. Ленюка
Короткий огляд (реферат): Михайло Павлович Ленюк – видатний математик і педагог, доктор фізико-математичних наук, професор, академік АН ВШ України, професор кафедри диференціальних рівнянь Чернівецького національного університету імені Юрія Федьковича завідувач кафедри інформаційних систем Чернівецького факультету Національного технічного університету «Харківський політехнічний інститут».; Mykhaylo P. Lenyuk - an outstanding mathematician and educator, doctor of physical and mathematical sciences, professor, academician of Higher School of Ukraine, professor of differential equations Chernivtsi National University of handicrafts Head of Information Systems Chernivtsi Department, National Technical University "Kharkiv Polytechnic Institute".2013-11-19T00:00:00ZЗмістhttp://elartu.tntu.edu.ua/handle/123456789/33742018-01-11T19:39:31Z2013-11-19T00:00:00ZНазва: Зміст2013-11-19T00:00:00Z